Specifications Index
TRACKER SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Axle Retaining Bolt | 41 Ft. Lbs. (55 N.m) | ||
| Battery | BATTERY SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING SEQUENCE | ||
| Brakes | BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | |||
| 2.0L | 2.0L TRACKER BELT ROUTING | ||
| 2.5L | 2.5L TRACKER BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 15 psi or specification stamped on cap. | ||
| Thermostat R & I | 2.0LTHERMOSTAT REPLACEMENT 2.5L THERMOSTAT REPLACEMENT |
||
| Water Pump R & I` | 2.0L WATER PUMP 2.5L WATER PUMP |
||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | With engine at normal operating temperature, oil pressure range should be 56-67 psi (3.9-4.7 kg/cm2 ) at 4000 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2.5L | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | Normal oil pressure is 47-61 psi (330-430 kPa) at 4000 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | 51 Ft. Lbs. (70 N.m) | ||
| Fuel System | |||
| Pressure Specification | 36-43 psi (248.2-296.5 kPa) Pressure should maintain at least 25 psi (172.4 kPa) for one minute after fuel pump is turned off. |
||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE TEST (2.0L) FUEL SYSTEM PRESSURE TEST (2.5L) |
||
| Ignition | |||
| Firing Order & Cylinder Identification | See FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Not equipped with high tension wires. Ignition coils are connected directly to spark plugs by boots. | ||
| Ignition Wires (Routing) | N/A | ||
| Spark Plug | SPARK PLUGS | ||
| Type | Denso K20PR-U11 or SK16PR11 NGK BKR6E11 or 1FR5J11 |
||
| Gap | .039-.043 In. (1.0-1.1 mm) | ||
| Torque | 18 Ft. Lbs. (25 N.m) | ||
| Starting | |||
| Starter | STARTER MOTOR SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | TRACKER | ||
| Torque | Tie Rod Lock Nuts 47 Ft.Lbs. (65 N.m) | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 74 Ft. Lbs. (100 N.m) | ||