LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2004 >> Impala SS >> Repair and Diagnosis >> External Pages >> Different car >> Section 247 (Cruise Control System) >> Diagnostic Information and Procedures >> Cruise Control Inoperative/Malfunctioning >> Test Description
July 1: So it begins. Don't worry, this is not in the correct legal jurisdiction!

Test Description

WARNING: This page is about a different car, the 2006 Pontiac Montana SV6, 2006 Chevrolet Uplander, and 2006 Buick Terraza. However, it is still accessible from the selected car via links, so may be relevant.

The number below refers to the step number on the diagnostic path.

  1. 26:  DTCs will set in the PCM when you perform this diagnostic table.
Cruise Control Inoperative/Malfunctioning

Step Action Values Yes No
Schematic Reference: Cruise Control Schematics 
Connector End View Reference: Master Electrical Component List in Wiring Systems
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 Is DTC P0573 current in the powertrain control module (PCM)? - Go to DTC P0573 in Lighting Systems Go to Step 3 
3
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Turn the cruise control On/Off switch OFF.
  4. With the scan tool, observe the following cruise control parameters in the Body and Accessories Cruise Control data list:
    • Cruise On/Off Switch
    • Cruise Resume/Accel Switch
    • Cruise Set/Coast Switch
Do any of the parameters listed above display On?		 - Go to Step 13  Go to Step 4 
4
  1. With the scan tool, observe the Cruise On/Off Switch parameter.
  2. Turn the cruise On/Off switch ON.
Does the Cruise On/Off Switch parameter display On?		 - Go to Step 5  Go to Step 9 
5
  1. With the scan tool, observe the Cruise Set/Coast Switch parameter.
  2. Press and hold the Set/Coast switch.
Does the Cruise Set/Coast Switch parameter display On?		 - Go to Step 6  Go to Step 11 
6
  1. With the scan tool, observe the Cruise Resume/Accel Switch parameter.
  2. Press and hold the Resume/Accel switch.
Does the Cruise Resume/Accel Switch parameter display On?		 - Go to Step 7  Go to Step 11 
7
  1. Turn OFF the ignition.
  2. Disconnect C3 at the body control module (BCM).
  3. Turn ON the ignition, with the engine OFF.
  4. With a DMM, measure the voltage of the cruise control cancel signal circuit.
Does the voltage measure at or greater than the specified voltage?		 0.5 V Go to Step 19  Go to Step 8 
8
  1. Activate and hold the cruise control cancel switch.
  2. With a DMM, measure the voltage of the cruise control cancel signal circuit.
Does the voltage measure at the specified voltage?		 B+ Go to Step 12  Go to Step 20 
9
  1. Turn OFF the ignition.
  2. Remove the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
  3. Disconnect C6.
  4. Turn ON the ignition, with the engine OFF.
  5. Connect a test lamp between the ignition 1 voltage circuit and a good ground.
Does the test lamp illuminate?		 - Go to Step 10  Go to Step 22 
10
IMPORTANT: The cruise control on/off switch must be turned ON in order to correctly view the Cancel switch, set/coast switch and the resume/accel switch resistance values with the DMM.
  1. With a DMM, measure the resistance of the cruise control switch between the ignition 1 voltage circuit and the cruise control set/coast and resume/accelerate switch signal circuit at the cruise control switch.
  2. Individually activate and hold the cruise control function switches while measuring the resistance of the cruise control function switches.
Do the cruise control function switch resistance values measure between the specified values?		 Off = O.L.
On = 7.8 K-8.6 K Ω
Resume = 2.7 K-3.0 K Ω
Set = 1.2 K-1.3 K Ω
Cancel = 0-1 K Ω		 Go to Step 15  Go to Step 16 
11
IMPORTANT: The cruise control on/off switch must be turned ON in order to correctly view the Cancel switch, set/coast switch and the resume/accel switch resistance values with the DMM.
  1. Turn OFF the ignition.
  2. Remove the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
  3. Disconnect C6.
  4. With a DMM, measure the resistance of the cruise control switch between the ignition 1 voltage circuit and the cruise control set/coast and resume/accelerate switch signal circuit at the cruise control switch.
  5. Individually activate and hold the cruise control function switches while measuring the resistance of the cruise control function switches.
Do the cruise control function switch resistance values measure between the specified values?		 Off = O.L.
On = 7.8 K-8.6 K Ω
Resume = 2.7 K-3.0 K Ω
Set = 1.2 K-1.3 K Ω
Cancel = 0-1 K Ω		 Go to Step 15  Go to Step 16 
12
  1. Turn OFF the ignition.
  2. Connect C3 at the BCM.
  3. Disconnect the throttle actuator control (TAC) module.
  4. Turn ON the ignition, with the engine OFF.
  5. With a DMM, measure the voltage of the stop lamp switch signal circuit.
Does the voltage measure greater than the specified value?		 8.5 V Go to Step 18  Go to Step 21 
13
  1. Turn OFF the ignition.
  2. Remove the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
  3. Disconnect C6.
  4. Turn ON the ignition, with the engine OFF.
  5. With the scan tool, observe the following cruise control parameters:
    • Cruise On/Off Switch
    • Cruise Resume/Accel Switch
    • Cruise Set/Coast Switch
Do any of the parameters listed above display On?		 - Go to Step 14  Go to Step 16 
14 Test the cruise control set/coast and resume/accel switch signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 26  Go to Step 17 
15 Test the cruise control Set/Coast and Resume/Accel switch signal circuit for the following:
  • Short to ground
  • Open
  • High Resistance

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 26  Go to Step 17 
16 Inspect for poor connections at the harness connector of the cruise control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 26  Go to Step 23 
17 Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 26  Go to Step 25 
18 Inspect for poor connections at the harness connector of the TAC module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 26  Go to Step 24 
19 Repair the short to voltage in the cruise control cancel signal circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?		 - Go to Step 26  -
20 Repair the following in the cruise control cancel signal circuit:
  • Short to ground
  • Open
  • High Resistance

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?		 - Go to Step 26  -
21 Repair the open or the high resistance in the stop lamp switch signal circuit between the underhood fuse block and the TAC module. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?		 - Go to Step 26  -
22 Repair the open, the short to ground or the high resistance in the ignition 1 voltage circuit. Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you complete the repair?		 - Go to Step 26  -
23 Replace the cruise control switch. Refer to Cruise Control Switch Replacement .
Did you complete the replacement?		 - Go to Step 26  -
24 Replace the TAC module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
Did you complete the replacement?		 - Go to Step 26  -
25 Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
Did you complete the replacement?		 - Go to Step 26  -
26 
  1. Install the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
  2. Enable the inflatable restraint steering wheel module. Refer to SIR Disabling and Enabling Zone 3 in SIR.
  3. Use the scan tool in order to clear the PCM DTCs.
  4. Operate the cruise control system in order to verify the repair.
Does the cruise control system operate properly?		 - System OK Go to Step 2 
scientia non olet · About LEMON Manuals