LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2006 >> Uplander Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 265 (Engine Cooling System) >> Repair Instructions >> Radiator Replacement >> Removal Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Removal Procedure

WARNING: This page is about a different car, the 2007 Chevrolet Monte Carlo and 2007 Chevrolet Impala. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection (RPO LS4) or Battery Negative Cable Disconnection and Connection (RPOs LZE/LZ4/LZ9) .
    CAUTION: Before servicing any electrical component, the ignition and start switch must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.
  2. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement for the 3.5L engine or to Air Cleaner Assembly Replacement for the 3.9L engine or to Air Cleaner Assembly Replacement for the 5.3L engine.
  3. Drain the cooling system. Refer to Draining and Filling Cooling System (9C1, 9C3 Static Fill)  or Draining and Filling Cooling System (LS4 GE 47716 Fill)  or Draining and Filling Cooling System (LS4 Static Fill)  or Draining and Filling Cooling System (LZE, LZ4, LZ8, 9C1, 9C3, GE47716 Fill)  or Draining and Filling Cooling System (LZE, LZ4, LZ8 Static Fill) .
  4. Remove the engine mount struts. Refer to Engine Mount Strut Replacement for the 3.5L engine or to Engine Mount Strut Replacement for the 3.9L engine or to Engine Mount Strut Replacement for the 5.3L engine.
  5. Use J 38185  to reposition the upper radiator hose clamp from the radiator. See Special Tools .
  6. Remove the upper radiator hose from the radiator.
  7. Remove the powertrain control module (PCM) harness clip from the fan shroud.
  8. Remove the condenser tubes bracket bolt from the fan shroud.
  9. Remove the bolt that connects the fan shroud to the condenser hold down bracket.
    Fig 1: Identifying Fan Shroud To Condenser Hold Down Bracket Bolt
    GM1202860Courtesy of GENERAL MOTORS CORP.
  10. Remove the condenser hold down bracket from the radiator and condenser.
  11. Remove the cooling fan shroud bolts.
    Fig 2: View Of Cooling Fan Shroud Bolts
    GM1653094Courtesy of GENERAL MOTORS CORP.
  12. Remove the coolant reservoir hose from the fan shroud LS4 only.
  13. Remove the radiator vent hose from the right upper radiator tank LS4 only.
    14. Fig 3: View Of Fan Shroud To Radiator Upper Support Brackets
    GM1202856Courtesy of GENERAL MOTORS CORP.
  14. Remove the radiator upper support brackets and bolts that connect to the fan shroud.
  15. Disconnect the engine cooling fan motors electrical connectors.
  16. Remove the cooling fan motors electrical harness from the fan shroud clips.
  17. Remove the cooling fan shroud.
  18. Use J 38185  to reposition the lower radiator hose clamp from the radiator. See Special Tools .
  19. Remove the lower radiator hose from the radiator.
  20. Disconnect the transaxle oil cooler pipes from the radiator. Refer to Transmission Fluid Cooler Hose/Pipe Quick-Connect Fitting Replacement .
  21. Tilt the top of the radiator rearward.
  22. Lift the condenser from the mounting tabs on the radiator (2). Position the condenser aside.
    Fig 4: Identifying Condenser Hold Down Bracket & Mount Tabs
    GM1202952Courtesy of GENERAL MOTORS CORP.
  23. Remove the radiator.
scientia non olet · About LEMON Manuals