Remote Control Door Lock Receiver Scan Tool Information

Remote Control Door Lock Receiver Scan Tool Data Parameters

Parameter	Expected Value	Definition
Operating Conditions: Ignition ON
Battery Voltage Signal	Varies	The scan tool displays the current system battery voltage.
Fob 1 Battery	OK	The scan tool displays OK or Low. This is the state of the Fob 1 battery.
Fob 1 Function	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. The scan tool indicates the last keyless entry function received by the keyless entry transmitter programmed to the #1 slot.
Fob 1 Programmed	Yes	The scan tool displays Yes or No. Yes is displayed if a fob has been programmed in Slot #1.
Fob 2 Battery	OK	The scan tool displays OK or Low. This is the state of the Fob 2 battery.
Fob 2 Function	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. The scan tool indicates the last keyless entry function received by the keyless entry transmitter programmed to the #2 slot
Fob 2 Programmed	Yes	The scan tool displays Yes or No. Yes is displayed if a fob has been programmed in Slot #2.
Fob 3 Battery	OK	The scan tool displays OK or Low. This is the state of the Fob 3 battery.
Fob 3 Function	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. The scan tool indicates the last keyless entry function received by the keyless entry transmitter programmed to the #3 slot.
Fob 3 Programmed	Yes	The scan tool displays Yes or No. Yes is displayed if a fob has been programmed in Slot #3..
Fob 4 Battery	OK	The scan tool displays OK or Low. This is the state of the Fob 4 battery.
Fob 4 Function	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. The scan tool indicates the last keyless entry function received by the keyless entry transmitter programmed to the #4 slot.
Fob 4 Programmed	Yes	The scan tool displays Yes or No. Yes is displayed if a fob has been programmed in Slot #4.
Front Placard	Varies	This displays Counts.
Last Fob Used	Varies	The scan tool displays None, Fob 1, Fob 2, Fob 3, Fob 4 or Fob 5. This was the last Fob used, as monitored by the RCDLR.
Last key Pressed On Fob	Varies	The scan tool displays Unlock, Lock, Panic, remote Start, Rear Closure, Left Slide Door, Right Slide Door, Learn, or [No Key Press]. The scan tool indicates the last keyless entry function received by a valid keyless entry transmitter.
LF Pressure Sensor Mode	Varies	The scan tool displays Learn, Re-measure, Drive, Stationary, or Wake. This is the state of the left front pressure sensor.
LF Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the left front tire pressure.
LF Tire Press. Sensor Status	Normal	The scan tool displays Normal Mode, Fault, or Low Battery. This is the state of the left front tire pressure sensor.
LF Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the left front tire.
LR Pressure Sensor Mode	Varies	The scan tool displays Learn, Re-measure, Drive, Stationary, or Wake. This is the state of the left rear pressure sensor.
LR Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the left rear tire pressure.
LR Tire Press. Sensor Status	Normal	The scan tool displays Normal Mode, Fault, or Low Battery. This is the state of the left rear tire pressure sensor.
LR Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the left rear tire.
Rear Placard	Varies	This displays Counts.
RF Pressure Sensor Mode	Varies	The scan tool displays Learn, Re-measure, Drive, Stationary, or Wake. This is the state of the right front pressure sensor.
RF Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the right front tire pressure.
RF Tire Press. Sensor Status	Normal	The scan tool displays Normal Mode, Fault, or Low Battery. This is the state of the right front tire pressure sensor.
RF Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the right front tire.
RR Pressure Sensor Mode	Varies	The scan tool displays Learn, Re-measure, Drive, Stationary, or Wake. This is the state of the right rear pressure sensor.
RR Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the right rear tire pressure.
RR Tire Press. Sensor Status	Normal	The scan tool displays Normal Mode, Fault, or Low Battery. This is the state of the right rear tire pressure sensor.
RR Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the right rear tire.
Selected Front Tire Type	Varies	The scan tool displays N/A, P-Metric (S), P-Metric (X), Load Range C, Load Range D or Load Range E. This is the type of front tires used on the vehicle.
Selected Rear Tire Type	Varies	The scan tool displays N/A, P-Metric (S), P-Metric (X), Load Range C, Load Range D or Load Range E. This is the type of rear tires used on the vehicle.
TPM System Enabled	Yes	The scan tool displays Yes or No. Yes is displayed if the TPM system is enabled.