Fastener Specifications
Single Use Non-Threaded Fasteners/Components
| Application |
|---|
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
| Camshaft Cover Gasket |
| Combustion Fuel Injector Seal |
| Connecting Rod Bearing |
| Crankshaft Front Oil Seal |
| Crankshaft Rear Oil Seal |
| Cylinder Head Core Hole Plug |
| Cylinder Head Gasket |
| Engine Coolant Thermostat Gasket |
| Engine Oil Cooler Gasket |
| Exhaust Manifold Gasket |
| Fuel Injector Seal Ring |
| Fuel Injector Spacer |
| Fuel Pump Gasket |
| Fuel Pump Housing Seal |
| Intake Manifold Gasket |
| Oil Pump Screen Gasket |
| Oil Pump Seal |
| Piston Pin Retainer |
| Positive Crankcase Ventilation Hose Fitting |
| Positive Crankcase Ventilation Tube |
| Positive Crankcase Ventilation Valve |
| Thermostat Bypass Pipe Gasket |
| Throttle Body Gasket |
| Timing Chain Tensioner Gasket |
| Turbocharger Coolant Feed and Return Pipe Gasket |
| Turbocharger Coolant Feed and Return Pipe Washer |
| Turbocharger Gasket |
| Turbocharger Oil Feed Pipe Gasket |
| Turbocharger Oil Feed Pipe Washer |
| Turbocharger Oil Return Pipe Gasket |
| Vacuum Pump Gasket |
| Vacuum Pump Seal |
| Valve Stem Oil Seal |
| Water Outlet Gasket |
| Water Pump Gasket |
Single Use Threaded Fastener/Component Tightening Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Automatic Transmission Flex Plate Bolt Refer to procedure for tightening sequence and torque values. |
Automatic Transmission Flex Plate Installation |
| Balance Shaft Sprocket Bolt | |
|
40 N.m (30 lb ft) |
|
50 degrees |
| Camshaft Position Actuator Bolt | |
|
30 N.m (22 lb ft) |
|
100 degrees |
| Connecting Rod Bolt | |
|
25 N.m (18 lb ft) |
|
110 degrees |
| Crankshaft Balancer Bolt | |
|
150 N.m (111 lb ft) |
|
140 degrees |
| Cylinder Head Bolt Refer to procedure for tightening sequence and torque values. |
Cylinder Head Installation |
| Cylinder Head Core Hole Plug | 50 N.m (37 lb ft) |
| Cylinder Head Oil Gallery Plug | 40 N.m (30 lb ft) |
| Engine Front Cover Bolt - M10 Refer to procedure for tightening sequence and torque values. |
Engine Front Cover Installation |
| Engine Mount Bolt | 58 N.m (43 lb ft) |
| Exhaust Manifold Bolt Refer to procedure for tightening sequence and torque values. |
Exhaust Manifold Installation |
| Exhaust Manifold Brace Nut | 25 N.m (18 lb ft) |
| Fuel Feed Intermediate Pipe | |
|
15 N.m (11 lb ft) |
|
30 N.m (22 lb ft) |
| Fuel Pump Bolt | |
|
8 N.m (71 lb in) |
|
50 degrees |
| Lower Crankcase Bolt Refer to procedure for tightening sequence and torque values. |
Lower Crankcase Installation |
| Oil Filter | 3/4 to 1 full turn after gasket makes contact with the sealing surface on the filter mounting flange |
| Positive Crankcase Ventilation Valve Bolt | 10 N.m (89 lb in) |
| Turbocharger Nut Refer to procedure for tightening sequence and torque values. |
Camshaft Cover and Compressor Air Intake Turbocharger Installation (2nd Design Tamper-Proof PCV System) |
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Balance Chain Guide Bolt | 10 N.m (89 lb in) |
| Balancer Chain Tensioner Bolt | 10 N.m (89 lb in) |
| Balancer Shaft with Oil Pump Bolt Refer to procedure for tightening sequence and torque values. |
Balancer Shaft with Oil Pump Installation |
| Camshaft Bearing Cap Bolt Refer to procedure for tightening sequence and torque values. |
Intake and Exhaust Camshaft, Bearing Cap, and Lash Adjuster Installation |
| Camshaft Bearing Cap Bolt- Front Refer to procedure for tightening sequence and torque values. |
Camshaft Timing Chain and Tensioner Installation |
| Camshaft Cover Bolt Refer to procedure for tightening sequence and torque values. |
Camshaft Cover and Compressor Air Intake Turbocharger Installation (2nd Design Tamper-Proof PCV System) |
| Camshaft Cover Heat Shield Bolt | 10 N.m (89 lb in) |
| Camshaft Cover Plug | 35 N.m (26 lb ft) |
| Camshaft Position Actuator Solenoid Valve Bolt | 10 N.m (89 lb in) |
| Camshaft Position Sensor Bolt | 10 N.m (89 lb in) |
| Catalytic Converter Brace Bolt | 25 N.m (18 lb ft) |
| Crankshaft Position Sensor Bolt | 10 N.m (89 lb in) |
| Drive Belt Tensioner Bolt | 58 N.m (43 lb ft) |
| Engine Block Oil Gallery Plug | 65 N.m (48 lb ft) |
| Engine Block Oil Gallery Plug | 40 N.m (30 lb ft) |
| Engine Coolant Air Bleed Pipe Bolt | 10 N.m (89 lb in) |
| Engine Coolant Heater | 50 N.m (37 lb ft) |
| Engine Coolant Heater Hole Plug | 60 N.m (44 lb ft) |
| Engine Coolant Thermostat Housing Bolt | 10 N.m (89 lb in) |
| Engine Front Cover Bolt - M6 Refer to procedure for tightening sequence and torque values. |
Engine Front Cover Installation |
| Engine Front Cover Bolt - M8 Refer to procedure for tightening sequence and torque values. |
Engine Front Cover Installation |
| Engine Lift Front Bracket Bolt | 25 N.m (18 lb ft) |
| Engine Lift Rear Bracket Bolt | 25 N.m (18 lb ft) |
| Engine Mount Bolt | 100 N.m (74 lb ft) |
| Engine Mount Brace Bolt | 22 N.m (16 lb ft) |
| Engine Oil Cooler Bolt | 10 N.m (89 lb in) |
| Engine Oil Cooler Connector | 50 N.m (37 lb ft) |
| Engine Oil Level Indicator Switch Bolt | 10 N.m (89 lb in) |
| Engine Oil Pressure Sensor | 35 N.m (26 lb ft) |
| Exhaust Manifold Brace Bolt | 25 N.m (18 lb ft) |
| Exhaust Manifold Heat Shield Bolt | 14 N.m (124 lb in) |
| Fuel Feed Pipe Fitting | 30 N.m (22 lb ft) |
| Fuel Feed Pipe Clip Stud | 10 N.m (89 lb in) |
| Fuel Injection Fuel Rail Bolt Refer to procedure for tightening sequence and torque values. |
Fuel Rail and Injectors Installation |
| Fuel Injection Fuel Rail Fuel Pressure Sensor | 33 N.m (24 lb ft) |
| Fuel Pump Shield Bolt | 10 N.m (89 lb in) |
| Ignition Coil Bolt | 10 N.m (89 lb in) |
| Intake Manifold Bolt Refer to procedure for tightening sequence and torque values. |
Intake Manifold Installation |
| Knock Sensor Bolt | 25 N.m (18 lb ft) |
| Lower Crankcase Bolt Refer to procedure for tightening sequence and torque values. |
Lower Crankcase Installation |
| Lower Oil Pan Bolt Refer to procedure for tightening sequence and torque values. |
Oil Pan Installation |
| Manifold Absolute Pressure Sensor Bolt | 5 N.m (44 lb in) |
| Oil Pan Baffle Bolt | 10 N.m (89 lb in) |
| Oil Pan Bolt Refer to procedure for tightening sequence and torque values. |
Oil Pan Installation |
| Oil Pan Bolt Refer to procedure for tightening sequence and torque values. |
Oil Pan Installation |
| Oil Pan Bolt - Transmission [2x] | 25 N.m (18 lb ft) |
| Oil Pan Drain Plug | 25 N.m (18 lb ft) |
| Oil Pump Suction Pipe Bolt | 10 N.m (89 lb in) |
| Oil Pump Flow Control Valve Bolt | 10 N.m (89 lb in) |
| Oil Pump Flow Control Valve Heat Shield Fastener | 9 N.m (80 lb in) |
| Oil Pump Flow Control Valve Heat Shield Fastener | 58 N.m (43 lb ft) |
| Piston Oil Nozzle Bolt | 10 N.m (89 lb in) |
| Positive Crankcase Ventilation Hose Fastener | 12 N.m (106 lb in) |
| Positive Crankcase Ventilation Hose Fitting Bolt | 8 N.m (71 lb in) |
| Thermostat Bypass Pipe Bolt | 10 N.m (89 lb in) |
| Throttle Body Bolt | 10 N.m (89 lb in) |
| Timing Chain Guide Bolt | 25 N.m (18 lb ft) |
| Timing Chain Tensioner Bolt | 25 N.m (18 lb ft) |
| Timing Chain Tensioner Shoe Bolt | 25 N.m (18 lb ft) |
| Transmission Bolt @ Oil Pan | 58 N.m (43 lb ft) |
| Turbocharger Bypass Valve Solenoid Bolt | 8 N.m (71 lb in) |
| Turbocharger Coolant Feed Pipe Bolt | 35 N.m (26 lb ft) |
| Turbocharger Coolant Feed Pipe Bolt | 10 N.m (89 lb in) |
| Turbocharger Coolant Return Pipe Bolt | 35 N.m (26 lb ft) |
| Turbocharger Heat Shield Bolt | 14 N.m (124 lb in) |
| Turbocharger Exhaust Pipe Stud | 25 N.m (18 lb ft) |
| Turbocharger Oil Feed Pipe Bolt | 35 N.m (26 lb ft) |
| Turbocharger Oil Feed Pipe Bolt | 10 N.m (89 lb in) |
| Turbocharger Oil Return Pipe Bolt | 10 N.m (89 lb in) |
| Turbocharger Wastegate Actuator Bolt | 8 N.m (71 lb in) |
| Turbocharger Wastegate Regulator Solenoid Valve Bolt | 8 N.m (71 lb in) |
| Vacuum Pump Bolt | 10 N.m (89 lb in) |
| Water Outlet Bolt | 10 N.m (89 lb in) |
| Water Pump Bolt Refer to procedure for tightening sequence and torque values. |
Water Pump Installation |