Removal Procedure

WARNING:

Refer to Glass and Sheet Metal Handling Warning

WARNING:

While operating, electrical control modules can produce heat and become hotter than their surroundings. To prevent burns allow sufficient time for the module to cool before removal.

CAUTION:

If a vehicle is equipped with a head curtain inflator module ensure that the inflator module and tether are undamaged. If tether or curtain airbag are damaged in any way, they must be replaced.

CAUTION:

Use care when working around the head curtain inflator module. Sharp tools may puncture the curtain airbag. If the head curtain inflator module is damaged in any way, it must be replaced.

Disable the SIR system. SIR Disabling and Enabling
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Windshield Wiper Arm - Left Side and Right Side (3) - Remove [2x]
1. Using the appropriate trim tool, remove the windshield wiper arm finish cap (1) from the windshield wiper arm (3).
2. Windshield Wiper Arm Nut - Left Side and Right Side (2) - Remove [2x]
3. Use the BO 49385 Wiper Arm Puller to remove the wiper arm (3) from the wiper motor pivot shaft.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Front Fender Rear Air Inlet Seal - Left Side and Right Side (2) - Remove [2x]
1. Front Fender Rear Air Inlet Seal Retainer (1) - Remove [2x]
2. Front Fender Rear Air Inlet Seal (2) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Front Compartment Side Sight Shield - Left Side and Right Side (2) - Remove [2x]
1. Front Compartment Side Sight Shield Retainer (1) - Remove [4x]
2. Front Compartment Side Sight Shield (2) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Air Inlet Grille Panel Extension - Left Side and Right Side (1) - Remove [2x]
1. Apply two layers of masking tape around the top edge of the service part to prevent paint damage.
2. Using a suitable plastic trim tool, carefully release the air inlet grille panel extension clips.
3. Remove the air inlet grille panel extension (1) from the air inlet grille panel and upper front fender.
Courtesy of GENERAL MOTORS COMPANY

Air Inlet Grille Panel (2) - Remove
1. Air Inlet Grille Panel Retainer (1) - Remove [8x]
2. Disconnect the windshield washer nozzle hose from the windshield washer pump hose.
3. Lift the front edge of the air inlet grille panel (2) and slide the panel forward from both hood hinges to remove.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Left side shown, right side similar.

Reposition the weatherstrip as necessary.
Pull the windshield garnish molding (1) rearwards to release the tether from the A pillar.

NOTE:

Tether and Bolt are integral to the Windshield Garnish Molding.

Access the windshield garnish bolt (2) which is located on the backside of the windshield garnish molding (1) and secures the tether to the A pillar.
Windshield Garnish Molding Bolt - Left Side and Right Side (2) - Remove [2x]
Disconnect the electrical connector. [2x]
Windshield Garnish Molding - Left Side and Right Side (1) - Remove [2x]
Courtesy of GENERAL MOTORS COMPANY

Using a plastic trim tool, carefully pry downward on the cover to release from windshield.
Squeeze tabs on insert and pull apart from cover.

NOTE:

The windshield multifunction sensor mount bracket cover and cover insert has to be removed as a single unit from the windshield surface to prevent damage to mirror.

Windshield Multifunction Sensor Mount Bracket Cover Insert (1) - Remove
Courtesy of GENERAL MOTORS COMPANY

Pull downward to completely remove the windshield multifunction sensor mount bracket cover (1) from windshield.

NOTE:

The windshield multifunction sensor mount bracket cover and cover insert has to be removed as a single unit from the windshield surface to prevent damage to mirror.

Windshield Multifunction Sensor Mount Bracket Cover (1) - Remove
Courtesy of GENERAL MOTORS COMPANY

Release the retaining tabs.
Front View Camera (1) - Remove
Disconnect the electrical connector.
Courtesy of GENERAL MOTORS COMPANY

Disconnect the electrical connector.
Inside Rearview Mirror Bolt (1) - Remove
Inside Rearview Mirror (2) - Remove

{If equipped} Windshield Outside Moisture/Ambient Light and Humidity Sensor - Remove

Courtesy of GENERAL MOTORS COMPANY

Roof Wiring Harness (1) @ Wiring Harness Retainer - Reposition

Courtesy of GENERAL MOTORS COMPANY

Release the retaining tabs.

Disconnect the electrical connector.
Windshield Outside Moisture/Ambient Light and Humidity Sensor (1) - Remove

Cover to protect the following parts from broken glass:
- Upper Dash Pad
- The defroster outlets and A/C outlets
- The seats and carpeting
{If equipped} Remove the lower windshield supports from the cowl panel.

NOTE:

Before cutting out a stationary window, apply a double layer of masking tape around the perimeter of the painted surfaces and the interior trim.

{If equipped} Using the appropriate tool, carefully cut around the lace, start in the center working from side to side of the window to access the urethane adhesive bead.
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Keep the cutting edge of the tool against the window.

Use BO-24402-A Glass Sealant Remover (1) to remove the window.
- Leave a base of urethane on the pinchweld flange.
- The only suitable lubrication is clear water.
Courtesy of GENERAL MOTORS COMPANY

With the aid of an assistant, remove the windshield (1) and locating pin (2) from the vehicle.