LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Dodge and Ram >> 1993 >> Stealth Base, Automatic >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Tests W/Codes >> Diagnostic Tests >> Code 25: Barometric Pressure Sensor
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Code 25: Barometric Pressure Sensor

NOTE: Barometric (BARO) pressure sensor is built into airflow sensor. For code 25 test purposes, the airflow sensor will be referred to as the BARO pressure sensor. For component terminal identification, see AIRFLOW SENSOR under TERMINAL IDENTIFICATION  . For wiring diagrams, see WIRING DIAGRAMS article.
  1. Manufacturer does not provide component testing procedure without scan tester. Turn ignition switch to ON position. Using scan tester, read sensor pressure. See BARO PRESSURE SENSOR SPECIFICATIONS  table. If pressure is not as specified, replace BARO pressure sensor. If pressure is as specified, go to next step.
    BARO PRESSURE SENSOR SPECIFICATIONS

    Altitude: Ft. (M) Pressure: In. Hg
    0 (0) 29.92
    1969 (600) 27.95
    3937 (1200) 25.98
    5906 (1800) 24.02
  2. Disconnect BARO pressure sensor connector. Using DVOM, check for continuity between chassis ground and specified BARO pressure sensor connector terminal. See BARO PRESSURE SENSOR GROUND CIRCUIT ID  table. If continuity does not exist, repair wiring harness as necessary. If continuity exists, go to next step.
    BARO PRESSURE SENSOR GROUND CIRCUIT ID

    Application Terminal No.
    All Models 5
  3. On Stealth and 3000GT, go to step 5. On all other models, with BARO pressure sensor disconnected, disconnect ECM connector. Check for continuity between specified ECM connector terminal and BARO pressure sensor connector terminal. See BARO PRESSURE SENSOR TO ECM CIRCUIT ID  table. If continuity does not exist, repair wiring harness as necessary. If continuity exists, go to next step.
    BARO PRESSURE SENSOR TO ECM CIRCUIT ID

    Application BARO Terminal No. ECM Terminal No.
    Diamante 1 61
    2 65
    All Models 2 65
  4. With BARO pressure sensor connector and ECM connector disconnected, turn ignition switch to ON position. Check for voltage between chassis ground and BARO pressure sensor connector terminal No. 1. If voltage is not 4.8-5.2 volts, replace ECM. If voltage is as specified, condition required to set code is not present at this time. Test is complete. Intermittent problem may exist. See TESTS W/O CODES article.
  5. With BARO pressure sensor connector disconnected, turn ignition switch to ON position. Check for voltage between chassis ground and specified BARO pressure sensor connector terminal. See BARO PRESSURE SENSOR POWER SUPPLY CIRCUIT ID  table. If voltage is not 4.8-5.2 volts, repair wiring harness as necessary. If voltage is as specified, go to next step.
    BARO PRESSURE SENSOR POWER SUPPLY CIRCUIT ID

    Application Terminal No.
    All Models 1
  6. With BARO pressure sensor connector and ECM connector disconnected, ground ECM connector terminal No. 16 (terminal No. 65 on Stealth and 3000GT). Using DVOM, check for continuity between chassis ground and specified BARO pressure sensor connector terminal. See ECM TO BARO PRESSURE SENSOR GROUND CIRCUIT ID  table. If continuity does not exist, repair wiring harness as necessary. If continuity exists, condition required to set code is not present at this time. Test is complete. Intermittent problem may exist. See TESTS W/O CODES article.
    ECM TO BARO PRESSURE SENSOR GROUND CIRCUIT ID

    Application Terminal No.
    Stealth & 3000GT 1
scientia non olet · About LEMON Manuals