Common Specs & Procedures
DURANGO COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM | ||
| Torque | FASTENER TORQUE | ||
| Axle Nut/Hub Nut | |||
| Front | 100 ft. lbs. (135 N.m) | ||
| Rear | 229 ft. lbs. (300 N.m) | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | Base Brakes: STANDARD PROCEDURE , Antilock Brakes: STANDARD PROCEDURE | ||
| Disc Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | Base Brakes: TORQUE , Antilock Brakes: TORQUE | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | GENERATOR RATINGS | ||
| Torque | TORQUE | ||
| Drive Belts | |||
| Adjustment | Serpentine belt used, not adjustable | ||
| Drive Belt Routing | See appropriate "Accessory Drive Belt Routing" figure under REMOVAL . | ||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | 16-20 psi (110-138 kPa) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | PUMP, WATER | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil Pressure | Refer to OIL PRESSURE table under SPECIFICATIONS . | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 5.7L | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil pressure | At Curb Idle Speed (MIN): 4 psi (25 kPa), @ 3000 RPM: 25-110 psi (170-758 kPa), If pressure is zero at curb idle, DO NOT run engine. | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 70 ft. lbs. (95 N.m) | ||
| Fuel System | |||
| Pressure Specification | 58 psi +/- 2 psi (407 kPa +/- 34 kPa) | ||
| Fuel Pressure Test Procedure | Refer to CHECKING THE FUEL DELIVERY SYSTEM . | ||
| Fuel Filter Location | FILTER, FUEL | ||
| Fuel Filter R & I | MODULE, FUEL PUMP | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 3.6L | |||
| Type | RER8ZWYCB4 | ||
| Gap | .040 in. (1.0 mm) | ||
| Torque | 13 ft. lbs. (17.5 N.m) | ||
| 5.7L | |||
| Type | REC14MCC4 | ||
| Gap | .040 in. (1.0 mm) | ||
| Torque | 13 ± 2 ft. lbs. (18 ± 3 N.m) NOTE: Torque critical tapered design. Do not exceed 15 ft. lbs. | ||
| Starting | |||
| Starter | STARTING SYSTEM | ||
| Torque | TORQUE | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT | ||
| Torque | SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | SPECIFICATIONS | ||