LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Dodge and Ram >> 2014 >> Durango R/T, AWD >> Repair and Diagnosis >> Accessories & Equipment >> Memory Modules >> (Memory Seat Module (MSMD) - Electrical Diagnostics) >> DTC Troubleshooting >> B1D5E-13-Power Seat Switch - Circuit Open >> Diagnostic Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Test

  1. CHECK IF THE DTC IS ACTIVE 
    1. Ignition on, engine not running.
    2. With the scan tool, record and erase Memory Seat Module-Driver (MSMD) DTCs.
    3. Cycle the ignition switch from off to on.
    4. Cycle the Power Seat Switch to all positions.
    5. With the scan tool, read MSMD DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  2

      No 

      • Go To  6
  2. CHECKING THE DRIVER SEAT SWITCH MUX RETURN CIRCUIT 
    1. Turn the ignition off.
    2. Disconnect the Driver Seat Switch harness connector.
    3. Using the Driver Seat Switch Continuity chart, measure the resistance of the Driver Seat Switch in the Off position.

      Is the resistance within specifications?

      Yes 

      • Go To  3

      No 

  3. CHECK THE (P599) DRIVER SEAT SWITCH MUX RETURN CIRCUIT FOR AN OPEN 
    1. Disconnect the MSMD C7 harness connector.
    2. Measure the resistance of the (P599) Driver Seat Switch Mux Return circuit between the MSMD C7 harness connector and the Driver Seat Switch harness connector.

      Is the resistance below 1.0 Ohm?

      Yes 

      • Go To  4

      No 

      • Repair the (P599) Driver Seat Switch Mux Return circuit for an open or high resistance.
      • Perform the POWER SEAT SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  4. CHECK THE (P339) DRIVER SEAT SWITCH FRONT VERTICAL/RECLINER SWITCH MUX CIRCUIT FOR AN OPEN 
    1. Measure the resistance of the (P339) Driver Seat Switch Front Vertical/Recliner Switch Mux circuit between the MSMD C7 harness connector and the Driver Seat Switch harness connector.

      Is the resistance below 1.0 Ohm?

      Yes 

      • Go To  5

      No 

      • Repair the (P339) Driver Seat Switch Front Vertical/Recliner Switch Mux circuit for an open or high resistance.
      • Perform the POWER SEAT SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  5. CHECK THE (P239) DRIVER SEAT SWITCH REAR VERTICAL/HORIZONTAL SWITCH MUX CIRCUIT FOR AN OPEN 
    1. Measure the resistance of the (P239) Driver Seat Switch Rear Vertical/Horizontal Switch Mux circuit between the MSMD C7 harness connector and the Driver Seat Switch harness connector.

      Is the resistance below 1.0 Ohm?

      Yes 

      No 

      • Repair the (P239) Driver Seat Switch Rear Vertical/Horizontal Switch Mux circuit for an open or high resistance.
      • Perform the POWER SEAT SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  6. CHECK THE WIRING AND CONNECTORS 
    1. The conditions necessary to set the DTC are not present at this time.
    2. Using the schematics as a guide, inspect the wiring and connectors specific to this circuit. Wiggle the wiring and connectors while checking for shorted and open circuits. Attempt to reproduce the condition by adjusting the seat(s).
    3. Check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals, and correct pin tension.
    4. Check Service Bulletins for any possible causes that may apply.

      Were there any problems found?

      Yes 

      • Repair as necessary.
      • Perform the POWER SEAT SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Test complete.
scientia non olet · About LEMON Manuals