Module Replacement Guide
WARNING: This page is about a different car, the 2016 Jeep Renegade. However, it is still accessible from the selected car via links, so may be relevant.
| MODULE | MODULE REPLACEMENT GUIDE - PASSIVE ENTRY EQUIPPED (BCM, Keys, ESL, PCM) | ||||||
|---|---|---|---|---|---|---|---|
| Condition 1 | Condition 2 | Condition 3 | Condition 4 | Condition 5 | Condition 6 | Condition 7 | |
| RF-HUB | New | Existing | Existing | Existing | Existing | New | New |
| FOBIKs (RKE Only) | Existing | New | Existing | Existing | Existing | New | Existing |
| BCM | Existing | Existing | New | Existing | Existing | Existing | New |
| PCM | Existing | Existing | Existing | New | Existing | Existing | Existing |
| ESL | Existing | Existing | Existing | Existing | New | Existing | Existing |
| PROGRAMMING ORDER | ASSOCIATED MODULE MISC. FUNCTION | ||||||
| 1 | RF-HUB Replace | Enable KEYs/FOBIKs (Only the new FOBIK needs to be present, previously stored FOBIKs will remain enabled.) | BCM replacement | Flash the ECM/PCM if the Spare Part is supplied without software | Transfer secret key to ESL / ECM | RF-HUB Replace | BCM replacement (first phase, at a certain point will be asked to configure the RFH, at that point run the RFH replacement, after the RFH replacement and the Disable Fobiks procedures run again the BCM replacement procedure in order to complete the BCM configuration) |
| 2 | Disable KEYs/FOBIKs (Only if the procedure did not run automatically after the RFH replacement procedure. All FOBIKs should be present, but the FOBIKs not present at this time will be temporarily disabled. It will be possible to re-enable them by running the Enable KEYs/FOBIKs procedure.) | BCM Replaced (in Vehicle Prep) | Run BCM ECU Reset (Found under the Diagnostic Procedures Tab of the Vehicle View screen) | Control unit replacement (If available will be found in the ECM ECU.) | PROXI alignment procedure | Disable KEYs/FOBIKs ONLY using the already stored FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure) | RFH replacement |
| 3 | RFH_TPM Update FF_FR Axle Nom Tire Press Val (only if the vehicle is equipped with TPM sensors, or if the current pressure value set by the RFH replacement routine is different from the expected due to aftermarket tire size on the vehicle.) | Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.) | RF-HUB Replace | Enable KEYs/FOBIKs ONLY using the new FOBIK(s) and eventually FOBIKs not presented during the Disable KEYs/FOBIKs procedure (Only the new or previously disabled FOBIK needs to be present, previously stored FOBIKs will remain enabled.) | Disable KEYs/FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure) | ||
| 4 | Program Left Front Tire Sensor ID, Program Left Rear Tire Sensor ID, Program Right Front Tire Sensor ID, and Program Right Rear Tire Sensor ID | PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.) | Update Front and Rear Axle Nominal Tire Pressure Values | BCM replacement (second phase, in order to complete the BCM configuration) | |||
| 5 | Program Tire Sensor IDs | Program Left Front Tire Sensor ID, Program Left Rear Tire Sensor ID, Program Right Front Tire Sensor ID, and Program Right Rear Tire Sensor ID | |||||
| MODULE | MODULE REPLACEMENT GUIDE - PASSIVE ENTRY EQUIPPED (BCM, Keys, ESL, PCM) | ||||||
|---|---|---|---|---|---|---|---|
| Condition 8 | Condition 9 | Condition 10 | Condition 11 | Condition 12 | Condition 13 | ||
| RF-HUB | New | New | Existing | Existing | Existing | New | |
| FOBIKs (RKE Only) | Existing | Existing | Existing | Existing | Existing | New | |
| BCM | Existing | Existing | New | New | Existing | New | |
| PCM | New | Existing | New | Existing | New | New | |
| ESL | Existing | New | Existing | New | New | New | |
| PROGRAMMING ORDER | ASSOCIATED MODULE MISC. FUNCTION | ||||||
| 1 | RF-HUB Replace | RF-HUB Replace | BCM replacement | BCM replacement | Flash the ECM/PCM if the Spare Part is supplied without software | RF-HUB Replace | |
| 2 | Disable KEYs/FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure) | Disable KEYs/FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure) | Run BCM ECU Reset (Found under the Diagnostic Procedures Tab of the Vehicle View screen) | Run BCM ECU Reset (Found under the Diagnostic Procedures Tab of the Vehicle View screen) | Control unit replacement (If available will be found in the ECM ECU.) | Disable KEYs/FOBIKs ONLY using the already stored FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure) | |
| 3 | Flash the ECM/PCM if the Spare Part is supplied without software | Transfer secret key to ESL / ECM | Flash the ECM/PCM if the Spare Part is supplied without software | Transfer secret key to ESL / ECM | Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.) | Enable KEYs/FOBIKs ONLY using the new FOBIK(s) and eventually FOBIKs not presented during the Disable KEYs/FOBIKs procedure (Only the new or previously disabled FOBIK needs to be present, previously stored FOBIKs will remain enabled.) | |
| 4 | Control unit replacement (If available will be found in the ECM ECU.) | PROXI alignment procedure | Control unit replacement (If available will be found in the ECM ECU.) | PROXI alignment procedure | PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.) | BCM replacement | |
| 5 | Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.) | RFH_TPM Update FF_FR Axle Nom Tire Press Val (only if the vehicle is equipped with TPM sensors, or if the current pressure value set by the RFH replacement routine is different from the expected due to aftermarket tire size on the vehicle.) | Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.) | Run BCM ECU Reset (Found under the Diagnostic Procedures Tab of the Vehicle View screen) | |||
| 6 | PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.) | Program Left Front Tire Sensor ID, Program Left Rear Tire Sensor ID, Program Right Front Tire Sensor ID, and Program Right Rear Tire Sensor ID | PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.) | Flash the ECM/PCM if the Spare Part is supplied without software | |||
| 7 | Control unit replacement (If available will be found in the ECM ECU.) | ||||||
| 8 | Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.) | ||||||
| 9 | PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.) | ||||||
| 10 | RFH_TPM Update FF_FR Axle Nom Tire Press Val (only if the vehicle is equipped with TPM sensors, or if the current pressure value set by the RFH replacement routine is different from the expected due to aftermarket tire size on the vehicle.) | ||||||
| 11 | Program Left Front Tire Sensor ID, Program Left Rear Tire Sensor ID, Program Right Front Tire Sensor ID, and Program Right Rear Tire Sensor ID | ||||||
| MODULE | MODULE REPLACEMENT GUIDE - ROTARY IGNITION (BCM, Keys, ESL, PCM) | ||||||
|---|---|---|---|---|---|---|---|
| Condition 1 | Condition 2 | Condition 3 | Condition 4 | Condition 5 | Condition 6 | Condition 7 | |
| BCM | New | Existing | Existing | Existing | New | New | New |
| FOBIKs (RKE Only) | Existing | New | Existing | Existing | New | Existing | Existing |
| PCM | Existing | Existing | New | Existing | Existing | New | Existing |
| ESL | Existing | Existing | Existing | New | Existing | Existing | New |
| PROGRAMMING ORDER | ASSOCIATED MODULE MISC. FUNCTION | ||||||
| 1 | BCM replacement | Program Keys (All the available Keys must be present during the procedure. Any keys not present at this time will be disabled FOREVER.) | Flash the ECM/PCM if the Spare Part is supplied without software | Transfer secret key to ESL / ECM | BCM replacement | BCM replacement | BCM replacement |
| 2 | Control unit replacement (If available will be found in the ECM ECU.) | PROXI alignment procedure | Program Keys (All the available Keys must be present during the procedure. Any keys not present at this time will be disabled FOREVER.) | Flash the ECM/PCM if the Spare Part is supplied without software | Transfer secret key to ESL / ECM | ||
| 3 | Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.) | Control unit replacement (If available will be found in the ECM ECU.) | PROXI alignment procedure | ||||
| 4 | PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.) | Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.) | |||||
| 5 | PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.) | ||||||
| MODULE | MODULE REPLACEMENT GUIDE - ROTARY IGNITION (BCM, Keys, ESL, PCM) | |||||
|---|---|---|---|---|---|---|
| Condition 8 | Condition 9 | |||||
| BCM | Existing | New | ||||
| FOBIKs (RKE Only) | Existing | New | ||||
| PCM | New | New | ||||
| ESL | New | New | ||||
| PROGRAMMING ORDER | ASSOCIATED MODULE MISC. FUNCTION | |||||
| 1 | Flash the ECM/PCM if the Spare Part is supplied without software | BCM replacement | ||||
| 2 | Control unit replacement (If available will be found in the ECM ECU.) | Program Keys (All the available Keys must be present during the procedure. Any keys not present at this time will be disabled FOREVER.) | ||||
| 3 | Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.) | Flash the ECM/PCM if the Spare Part is supplied without software | ||||
| 4 | PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.) | Control unit replacement (If available will be found in the ECM ECU.) | ||||
| 5 | Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.) | |||||
| 6 | PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.) | |||||