LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Dodge and Ram >> 2017 >> Viper GTC >> Repair and Diagnosis >> Engine Performance >> Testing & Diagnosis >> 8.4L - Pcm/TCM Programming, Checking For An Intermittent DTC, Powertrain Verification Test & Pre-Diagnostic Troubleshooting Procedure >> Standard Procedure >> Pcm / TCM Programming >> Additional Pcm / TCM Replacement Procedures
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Additional Pcm / TCM Replacement Procedures

NOTE:

Find the PCM/TCM Type for the vehicle, read and write down the steps, and then go to the step by step instructions for additional information on how to perform these procedures. 

If an EDC16-U31 PCM/ECM (2.0L) was replaced, perform the following additional steps and/or routines: 

  1. PCM/ECM Replaced - if WIN equipped
  2. Check PCM/ECM VIN - if NOT WIN equipped
  3. Program Variant Code

If an EDC16-C2 PCM/ECM (2.2L) was replaced, perform the following additional steps and/or routines: 

  1. PCM/ECM Replaced - if WIN equipped
  2. Check PCM/ECM VIN - if NOT WIN equipped
  3. IMA Rapid Calibration Test - Only on 06 PT AND up
  4. Injector Quantity Adjustment - Only on 06 PT AND up

If an EDC16-CP31 (3.0L) was replaced, perform the following additional steps and/or routines: 

  1. PCM/ECM Replaced - if WIN equipped
  2. Check PCM/ECM VIN - if NOT WIN equipped
  3. Diesel Particulate Filter (Used) Learning
  4. NOx Catalyst (New) Initialization
  5. Injector Quantity Adjustment
  6. IMA Rapid Calibration Test
  7. Fuel Mean Value Adaptation Initialization
  8. Exhaust Throttle Plate Adaptive Learn Position

If an EDC16-CP31-2 (2.8L) was replaced, perform the following additional steps and/or routines: 

  1. PCM/ECM Replaced - if WIN equipped
  2. Check PCM/ECM VIN - if NOT WIN equipped
  3. Injector Quantity Adjustment
  4. Program Variant Code
  5. ECU Replacement With Value Transfer - if the ECU to be replaced is still responsive
  6. ECU Replacement Without Value Transfer - if the ECU to be replaced is NOT responsive
  7. Fuel Mean Value Adaptation Initialization
  8. IMA Rapid Calibration Test
  9. Set Oil Dilution Mass Value

If a CM849 PCM/ECM (5.9L) was replaced, perform the following additional steps and/or routines: 

  1. PCM/ECM Replaced - if WIN equipped
  2. Check PCM/ECM VIN - if NOT WIN equipped

If a CM2100 PCM/ECM (6.7l) was replaced, perform the following additional steps and/or routines: 

  1. PCM/ECM Replaced - if WIN equipped
  2. Check PCM/ECM VIN - if NOT WIN equipped
  3. Enable / Disable Vehicle Features - need to enable features
  4. Injector Quantity Adjustment
  5. Reset Regenerative Filter Timers
  6. Mobile DeSoot - NO Minimum Required Soot Load

If an Aisin TCM was replaced, perform the following additional steps and/or routines: 

If an EATX TCM was replaced, perform the following additional steps and/or routines: 

If an NGC3 TCM ONLY was replaced, perform the following additional steps and/or routines: 

If an NGC4 TCM ONLY was replaced, perform the following additional steps and/or routines: 

  1. Quicklearn

If an EGS TCM was replaced, perform the following additional steps and/or routines: 

  1. Initialize EGS
scientia non olet · About LEMON Manuals