Diagnostic Code Index
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| C2006-16 | Battery voltage - Circuit Voltage Below Threshold |
| C2006-17 | Battery voltage - Circuit Voltage Above Threshold |
| C2010-16 | Battery voltage 2nd threshold - Circuit Voltage Below Threshold |
| C2010-17 | Battery voltage 2nd threshold - Circuit voltage above threshold |
| C2020-01 | ECU internal fault - General Electrical Failure |
| C2020-47 | ECU internal fault - Watchdog/safety μC failure |
| C2020-48 | ECU internal fault - Supervision software failure |
| C2020-94 | ECU internal fault - Unexpected operation |
| C2030-42 | ECU software failure - General memory failure |
| C2050-1C | Hall sensors supply - Circuit voltage out of range |
| C2060-09 | Hall sensor 1 - Component Failures |
| C2070-09 | Hall sensor 2 - Component Failures |
| C2080-09 | Motor 1 - Component Failures |
| C2080-64 | Motor 1 - Signal plausibility failure |
| C2090-09 | Motor 2 temperature sensor - Component failures |
| C2100-04 | Motor 1 - System Internal Failures |
| C2100-13 | Motor 1 - Circuit open |
| C2100-14 | Motor 1 - Circuit short to ground |
| C2100-15 | Motor 1 - Circuit short to battery |
| C2120-04 | Motor 2 - System Internal Failures |
| C2120-13 | Motor 2 - Circuit open |
| C2120-14 | Motor 2 - Circuit short to ground |
| C2120-15 | Motor 2 - Circuit short to battery |
| C2150-98 | Motor 1 power stage temp - Component or system over temperature |
| C2160-04 | Motor 1 power stage test failure - System Internal Failures |
| C2180-98 | Motor 2 power stage switch temp - Component or system over temperature |
| C2190-98 | Motor 2 power stage overload - Component or system over temperature |
| C2200-04 | Motor 2 power stage test - System Internal Failures |
| C2201-64 | OperationalModeStatus signal from Body Control Module - Signal invalid |
| C2202-64 | Implausible Data Received from BCM (Invalid Terrain Selector status CAN signal received from Body Control Module) - Signal plausibility failure |
| C2203-24 | 4WD Lock Switch - Signal Stuck High |
| C2204-24 | 4WD Low Switch - Signal Stuck High |
| C2206-64 | Implausible Data Received from BSM (Invalid Steering Angle CAN signal received from Body Control Module) - Signal plausibility failure |
| C2208-64 | Oversteering signal not available from brake3 message - Signal plausibility failure |
| C2209-64 | Understeering signal not available from brake3 message - signal plausibility failure |
| C2210-92 | Rear Drive Module Electronic Torque Manager actuator sensor - Performance or incorrect operation |
| C221B-64 | Eldfailsts signal not valid from brake7 message - signal plausibility failure |
| C221D-98 | Rear Drive Module ECU Driver output temperature high - Component or system temperature |
| C221E-64 | Brake pedal switch fail status - Signal plausibility failure |
| C221F-64 | Drive style status signal - Signal plausibility failure |
| C2220-54 | ETM calibration error - Missing calibration |
| C2224-64 | EngineSpeed signal NOT available from ENGINE1 message - Signal plausibility failure |
| C2225-64 | Enginests signal not available from engine1 message - signal plausibility failure |
| C2226-64 | Reversegearsts signal not available from engine1 message - signal plausibility failure |
| C2227-64 | Enginetorque signal not available from engine4 message - signal plausibility failure |
| C2228-64 | Gaspedalgradient signal not available from engine4 message - signal plausibility failure |
| C2229-64 | Gearengaged signal not available from transm2 message - signal plausibility failure |
| C2230-98 | ETM_ACTIVE_OVERHEAT_PROTECTION - Component or system over temperature |
| C2240-92 | ETM motor free running - Performance or incorrect operation |
| C2250-78 | Invalid Backlash Coupling - Alignment or adjustment incorrect |
| C2260-63 | System initialization time expired - Circuit/Component protection time-out |
| C2270-77 | Power Transfer Unit (PTU) Electronic Disconnect Actuator (EDA) sensor - Commanded position not reachable |
| C2280-92 | EDA current - Performance or incorrect operation |
| C2290-92 | EDA motor free running - Performance or incorrect operation |
| C2300-00 | RDM CLASSIFICATION NOT VALID - No Subtype information |
| C2400-55 | PROXI configuration - NOT configured OR Proxy data contains values "invalid" or not correct |
| C2501-87 | Missing CAN messages from Brake System Module or Body Control Module or Engine Control Module - Missing message |
| C2502-64 | CAN signals error notification received from Engine Control Module or Brake System Module or Body Control Module - Signal plausibility failure |
| C2503-87 | Instrument Panel Cluster (IPC) - Absent |
| C2504-87 | BRAKE1 - Missing message |
| C2506-64 | Transm2.shiftlevelposition - Signal Plausibility Failure |
| C2507-64 | Implausible Data Received from Brake System Module (Invalid engine torque request CAN signal received from Engine Control Module) - Signal plausibility failure |
| C2508-64 | Engine3.maxenginetorque - signal plausibility failure |
| C2509-64 | Implausible Data Received from ECM (Invalid Engine Torque Output CAN signal received from Engine Control Module) - Signal plausibility failure |
| C2510-64 | CAN signals error notification received from Brake System - Signal plausibility failure |
| C2511-64 | CAN signals error notification received from Transmission Control Module - Signal plausibility failure |
| C2512-64 | CAN signals error notification received from Body Control Module - Signal plausibility failure |
| U0001-88 | C CAN_1 Bus - Bus off |
| U1700-87 | Body Control Module (BCM) - Absent |
| U1701-87 | Engine Control Module (ECM) - Absent |
| U1702-87 | Electrical Power Steering (EPS) - Absent |
| U1706-87 | Brake System Module (BSM) - Absent |
| U1710-87 | BCM_COMMAND - Missing message |
| U1711-87 | Automatic/Robotic Gear Box NCA/NCR - Absent |
| U1952-83 | Implausible Data Received from Brake System Module (CAN message BRAKE1 integrity error) - Value of signal protection calculation incorrect |
| U1956-83 | Implausible Data Received from Brake System Module (CAN message BRAKE3 integrity error) - Value of signal protection calculation incorrect |
| U1958-83 | Implausible Data Received from Brake System Module (CAN message BSM_YRS_DATA integrity error) - Value of signal protection calculation incorrect |
| U1960-83 | Implausible Data Received from Engine Control Module (CAN message ENGINE1 integrity error) - Value of signal protection calculation incorrect |
| U1962-83 | Implausible Data Received from Engine Control Module (CAN message ENGINE3 integrity error -) Value of signal protection calculation incorrect |
| U1964-83 | Implausible Data Received from Engine Control Module (CAN message ENGINE4 integrity error) - Value of signal protection calculation incorrect |
| U1966-83 | Implausible Data Received from Electrical Power Steering (CAN message GE integrity error) - Value of signal protection calculation incorrect |
| U196C-83 | Implausible Data Received from Engine Control Module (CAN message MOT_TRANSM1 integrity error) - Value of signal protection calculation incorrect |
| U1970-83 | Implausible Data Received from Transmission Control Module (CAN message TRANSM3 integrity error) - Value of signal protection calculation incorrect |
| U1976-83 | Implausible Data Received from Body Control Module (CAN message BCM_COMMAND integrity error) - Value of signal protection calculation incorrect |
| U1978-83 | Implausible Data Received from Brake System Module (CAN message STATUSEPB integrity error) - Value of signal protection calculation incorrect |
| U197A-83 | Implausible Data Received from Transmission Control Module (CAN message TRANSM1 integrity error) - Value of signal protection calculation incorrect |
| U197C-83 | Implausible Data Received from Transmission Control Module (CAN message TRANSM2 integrity error) - Value of signal protection calculation incorrect |
| U1984-83 | Implausible Data Received from Brake System Module (CAN message WHEEL_SPEED integrity error) - Value of signal protection calculation incorrect |
| U198A-83 | Implausible Data Received from Brake System Module (CAN message BRAKE7 integrity error) - Value of signal protection calculation incorrect |
| U199A-87 | Lost Communication with BSM (CAN messages BRAKE3 OR BSM_YRS_DATA missing from Brake System Module) - Missing message |
| U199B-87 | Lost Communication with BSM (CAN messages BRAKE6 OR BRAKE7 OR BRAKE8 OR STATUS_EPB missing from Brake System Module) - Missing message |
| U2000-64 | WHEEL_SPEED_FRONT - Signal plausibility failure |
| U2001-64 | WHEEL_SPEED._REAR - Signal plausibility failure |
| U2002-87 | WHEEL_SPEED - Missing message |
| U2003-64 | Implausible Data Received from BSM (Invalid Lateral Acceleration CAN signal data received from Brake System Module) - Signal plausibility failure |
| U2004-64 | Implausible Data Received from BSM (Invalid Longitudinal Acceleration CAN signal received from Brake System Module) - Signal plausibility failure |
| U2005-64 | Implausible Data Received from ECM (Invalid Gas Pedal Position CAN signal received from Engine Control Module) - Signal plausibility failure |
| U2006-64 | Implausible Data Received from BSM (Invalid Parking Brake CAN signal received from Brake System Module) - Signal plausibility failure |