Specifications Index
MUSTANG SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Battery | Amps at -17.7°C (0°F) cold crank: 540 | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | See GENERATOR SPECIFICATIONS | ||
| Torque | See TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Information | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 16 Lbs. | ||
| Thermostat R & I | |||
| 4.6L V8 2V (VIN X) | THERMOSTAT | ||
| Water Pump R & I | |||
| 3.8L V6 | WATER PUMP | ||
| 4.6L V8 4V (VIN V) | WATER PUMP | ||
| 4.6L V8 2V (VIN X) | WATER PUMP | ||
| Engine Mechanical | |||
| 3.8L V6 | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | 40-125 psi (276-862 kPa) at 2500 RPM with engine at normal operating temperature. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 4.6L V8 4V (VIN V) | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | 20-45 psi (138-310 kPa) at 1500 RPM with engine at normal operating temperature. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 4.6L V8 2V (VIN X) | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | 20-45 psi (138-310 kPa) at 1500 RPM with engine at normal operating temperature. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab.From within Manager or Service Writer, click the "30/60/90 Interval" "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| 3.8L V6 | 59 Ft. Lbs. (80 N.m) IMPORTANT: Apply thread sealant to bolt threads. |
||
| 4.6L V8 4V (VIN V) | 63 Ft. Lbs. (85 N.m) | ||
| 4.6L V8 2V (VIN X) | See INSTALLATION | ||
| Fuel System | |||
| Fuel Filter Location | Under vehicle forward of fuel tank, mounted in bracket. | ||
| Pressure Release Procedure | |||
| 3.8L V6 | FUEL PRESSURE RELEASE & FUEL LINE CONNECTIONS | ||
| 4.6L V8 4V (VIN V) | FUEL PRESSURE RELEASE & FUEL LINE CONNECTIONS | ||
| 4.6L V8 2V (VIN X) | FUEL PRESSURE RELEASE | ||
| Pressure Specification (KOEO) | 35-45 psi (210-310 kPa) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE | ||
| Fuel Filter R & I | |||
| 3.8L V6 | FUEL FILTER | ||
| 4.6L V8 | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | IGNITION SYSTEM | ||
| Ignition Wires (Routing) | |||
| 3.8L V6 | FIRING ORDER & TIMING MARKS | ||
| 4.6L V8 | Coil On Plug | ||
| Spark Plugs | |||
| 3.8L V6 | |||
| Type | Motorcraft AWSF-44EE NOTE: Three different styles of platinum-enhanced spark plugs are produced for the 3.8L engine. Each spark plug has a different part number and use. AWSF-44E spark plugs have a platinum enhanced center electrode and are used in cylinders 4, 5 and 6. AWSF-44EG spark plugs have a platinum-enhanced ground (side) electrode and are used in cylinders 1, 2 and 3. If any spark plug is removed and re-installed, it MUST be installed in the same cylinder from which it was removed. If any spark is replaced, use only spark plugs with part number AWSF-44EE as listed on the vehicle emission control information label. This replacement spark plug has double platinum enhancement on both the center and ground electrode and may be used in all six cylinders. |
||
| Gap | 0.052-0.056 In. (1.32-1.42 mm) | ||
| Torque | 7-15 Ft. Lbs (10-20 N.m) | ||
| 4.6L V8 (4V) | |||
| Type | Motorcraft AWSF-32EE Three different styles of platinum enhanced spark plugs are produced for the 4.6L (4V) engine. Each spark plug has a different part number and use. AWSF-32E spark plugs have a platinum enhanced center electrode and are used in cylinders 5, 6, 7 and 8. AWSF-32EG spark plugs have a platinum enhanced ground (side) electrode, and are used in cylinders 1, 2, 3 and 4. If any spark plug is removed and re-installed, it MUST be installed in the same cylinder from which it was removed. If any spark plug is replaced, use only spark plugs with part number AWSF-32EE (as listed on the vehicle emission control information label). This replacement spark plug has double platinum enhancement on both the center and ground electrode and may be used in all eight cylinders. |
||
| Gap | 0.052-0.056 In. (1.32-1.42 mm) | ||
| Torque | 7-15 Ft. Lbs. (10-20 N.m) | ||
| 4.6L V8 (2V) | |||
| Type | Motorcraft AWSF-32PP Three different styles of platinum-enhanced spark plugs are produced for the 4.6L (2V) engine. If any spark plug is removed and re-installed, it must be installed in the same cylinder from which it was removed. Each spark plug has a different part number and use. AWSF-32P spark plugs have a platinum-enhanced center electrode and are used in cylinders 5, 6, 7 and 8. AWSF-32PG spark plugs have a platinum-enhanced ground (side) electrode, and are used in cylinders 1, 2, 3 and 4. If any spark plug is replaced, use only spark plugs with part number AWSF-32PP as listed on the vehicle emission calibration identification label. This replacement spark plug has double-platinum-enhancement on both the center and ground electrode and may be used in all eight cylinders. |
||
| Gap | 0.052-0.056 In. (1.32-1.42 mm) | ||
| Torque | 7-15 Ft. Lbs. (10-20 N.m) | ||
| Starting | |||
| Starter | STARTER MOTOR SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 85-104 Ft. Lbs. (115-142 N.m) | ||