DEM Diagnostic Trouble Code (DTC) Index
WARNING: This page is about a different car, the 2006 Mercury Montego, 2006 Ford Freestyle, and 2006 Ford Five Hundred. However, it is still accessible from the selected car via links, so may be relevant.
DEM DIAGNOSTIC TROUBLE CODE (DTC) INDEX
| DTC | Description | Source | Action |
|---|---|---|---|
| P0562 | System Voltage Low | DEM | REFER to CHARGING SYSTEM - GENERAL INFORMATION . |
| P0563 | System Voltage High | DEM | REFER to CHARGING SYSTEM - GENERAL INFORMATION . |
| P0602 | Differential Electronic Module (DEM) Programming Error | DEM | CLEAR DTCs. REPEAT the self-test. If DTC P0602 is retrieved, INSTALL a new DEM. REFER to INSTALLATION . CLEAR the DTCs. REPEAT the self-test. |
| P0606 | ECU Short to Ground or Open Circuit | DEM | CLEAR DTCs. REPEAT the self-test. If DTC P0606 is retrieved, INSTALL a new DEM. REFER to INSTALLATION . CLEAR the DTCs. REPEAT the self-test. |
| P0932 | Hydraulic Pressure Sensor Circuit | DEM | INSTALL a new Rear Axle Oil Temperature Sensor. REFER to REAR DRIVE AXLE AND DIFFERENTIAL . CLEAR the DTC. REPEAT the self-test. |
| P0937 | Hydraulic Oil Temperature Sensor Circuit | DEM | INSTALL a new Rear Axle Oil Temperature Sensor. REFER to REAR DRIVE AXLE AND DIFFERENTIAL . CLEAR the DTC. REPEAT the self-test. |
| P0939 | Hydraulic Oil Temperature Sensor Circuit Low Input | DEM | INSTALL a new Rear Axle Oil Temperature Sensor. REFER to REAR DRIVE AXLE AND DIFFERENTIAL . CLEAR the DTC. REPEAT the self-test. |
| P0940 | Hydraulic Oil Temperature Sensor Circuit High Input | DEM | INSTALL a new Rear Axle Oil Temperature Sensor. REFER to REAR DRIVE AXLE AND DIFFERENTIAL . CLEAR the DTC. REPEAT the self-test. |
| P0960 | Pressure Control Solenoid A Control Circuit Open | DEM | MONITOR the ABS wheel speed sensor PIDS to verify that the ABS module is transmitting the correct wheel speeds to the DEM. CHECK for fluid leaks in the active on-demand coupler. REPAIR as necessary. REFER to REMOVAL AND INSTALLATION . If no faults are found, INSTALL a new DEM. REFER to INSTALLATION . CLEAR the DTCs. REPEAT the self-test. |
| P0961 DEM code only (code can appear in TCM) | Pressure Control Solenoid A Control Circuit Range Performance | DEM | MONITOR the ABS wheel speed sensor PIDS to verify that the ABS module is transmitting the correct wheel speeds to the DEM. CHECK for fluid leaks in the active on-demand coupler. REPAIR as necessary. REFER to REMOVAL AND INSTALLATION . If no faults are found, INSTALL a new DEM. REFER to INSTALLATION . CLEAR the DTCs. REPEAT the self-test. |
| P0962 | Pressure Control Solenoid A Control Circuit Low | DEM | MONITOR the ABS wheel speed sensor PIDS to verify that the ABS module is transmitting the correct wheel speeds to the DEM. CHECK for fluid leaks in the active on-demand coupler. REPAIR as necessary. REFER to REMOVAL AND INSTALLATION . If no faults are found, INSTALL a new DEM. REFER to INSTALLATION . CLEAR the DTCs. REPEAT the self-test. |
| P1889 | Oil Pressure Pump Performance | DEM | INSTALL a new Active On-Demand Coupling Oil Pump. REFER to REMOVAL AND INSTALLATION . CLEAR the DTC. REPEAT the self-test. If DTC P1889 is still present, INSTALL the DEM kit (4C016) including all of the parts. REFER to INSTALLATION . CLEAR the DTCs. REPEAT the self test. |
| U0001 | High Speed CAN Communication Bus | DEM | REFER to PINPOINT TEST M: NO HIGH SPEED CONTROLLER AREA NETWORK (CAN) COMMUNICATION . |
| U0121 | Lost Communication With Anti-Lock Brake System (ABS) Control Module or PCM | DEM | REFER to PINPOINT TEST B: THE ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DOES NOT RESPOND TO THE DIAGNOSTIC TOOL . |
| U2050 | No Valid Application Added | DEM | RECONFIGURE the DEM using As-Built Data. |