LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2000 >> ZX2 Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1741 (Brake System - General Information) >> General Procedures >> Brake System Bleeding >> Manual
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Brake System Bleeding: Manual

WARNING: This page is about a different car, the 2006 Mercury Montego, 2006 Ford Freestyle, and 2006 Ford Five Hundred. However, it is still accessible from the selected car via links, so may be relevant.
WARNING:
  • Use of any other than approved DOT 3 brake fluid will cause permanent damage to brake components and will render the brakes inoperative. Failure to follow these instructions may result in personal injury.
  • Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in personal injury.
CAUTION:
  • Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.
  • Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the DOT 3 motor vehicle brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system.
NOTE:
  • Due to the complexity of the fluid path within the rear integral parking brake calipers, it is necessary to press and release the parking brake during the bleed procedure.
  • If the hydraulic control unit (HCU) or any component upstream of the HCU are installed new, carry out the Brake System Pressure Bleeding procedure, then the anti-lock HCU bleed procedure, followed by another Brake System Bleed procedure.
  • When any part of the hydraulic system has been disconnected for repair or installation of new components, air can get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been correctly connected. The hydraulic system can be bled manually or with pressure bleeding equipment. Bleeding the system with pressure bleeding equipment is the preferred method.
  1. Clean all the dirt from the area, remove the brake master cylinder reservoir cap and fill the brake master cylinder reservoir with the specified brake fluid.
    Fig 1: Identifying Brake Master Cylinder Fluid Reservoir Cap And Max Fill Line
    G03983412Courtesy of FORD MOTOR CO.
  2. Remove the rear bleeder cap and place a box end wrench on the RH rear bleeder screw. Attach a rubber drain tube to the RH rear bleeder screw and submerge the free end of the tube in a container partially filled with clean brake fluid.
    Fig 2: Locating Rubber Drain Tube On Bleeder Screw
    G03983413Courtesy of FORD MOTOR CO.
  3. Have an assistant hold firm pressure on the brake pedal.
  4. Loosen the RH rear bleeder screw until a stream of brake fluid comes out. While the assistant maintains pressure on the brake pedal, tighten the RH rear bleeder screw.
    • Press and release the parking brake 5 times.
    • Repeat until clear, bubble-free fluid comes out.
    • Refill the brake master cylinder reservoir as necessary.
  5. Tighten the RH rear bleeder screw and install the bleeder cap.
    • Tighten to 10 N.m (89 lb-in).
  6. Repeat Steps  3,  4,  5 and  6 for the LH rear bleeder screw.
  7. Remove the rear bleeder cap and place a box end wrench on the RH front brake caliper bleeder screw. Attach a rubber drain tube to the RH front brake caliper bleeder screw, and submerge the free end of the tube in a container partially filled with clean brake fluid.
    Fig 3: Locating Rubber Drain Tube
    G04655468Courtesy of FORD MOTOR CO.
  8. Have an assistant hold firm pressure on the brake pedal.
  9. Loosen the RH front brake caliper bleeder screw until a stream of brake fluid comes out. While the assistant maintains pressure on the brake pedal, tighten the RH front brake caliper bleeder screw.
    • Repeat until clear, bubble-free fluid comes out.
    • Refill the brake master cylinder reservoir as necessary.
    Fig 4: Locating RH Front Brake Caliper Bleeder Screw
    G04655469Courtesy of FORD MOTOR CO.
  10. Tighten the RH front brake caliper bleeder screw and install the bleeder cap.
    • Tighten to 12 N.m (9 lb-ft).
  11. Repeat Steps  8,  9,  10 and  11 for the LH front brake caliper bleeder screw.
scientia non olet · About LEMON Manuals