Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index
WARNING: This page is about a different car, the 2004 Mercury Monterey and 2004 Ford Freestar. However, it is still accessible from the selected car via links, so may be relevant.
ABS MODULE DIAGNOSTIC TROUBLE CODE INDEX
| DTC | Description | Source | Action |
|---|---|---|---|
| B1317 | Battery Voltage High | ABS Module | GO to PINPOINT TEST L . |
| B1318 | Battery Voltage Low | ABS Module | GO to PINPOINT TEST L . |
| B1342 | ECU Is Defective | ABS Module |
NOTE:
If other DTCs are present, REPAIR them before installing a new component. CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . REPEAT the self-test. |
| B2061 | LF ISO Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2062 | RF ISO Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2063 | LR ISO Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2064 | RR ISO Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2065 | TC ISO Valve Solenoid 1 Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2066 | TC ISO Valve Solenoid 2 Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2067 | LF Dump Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2068 | RF Dump Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2069 | LR Dump Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2070 | RR Dump Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2071 | TC Supply Valve Solenoid 1 Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2072 | TC Supply Valve Solenoid 2 Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2073 | ECA Valve Solenoid Overtemp | ABS Module | GO to PINPOINT TEST N . |
| B2477 | Module Configuration Failure | ABS Module | RECONFIGURE the ABS module. REFER to MODULE COMMUNICATIONS NETWORK . CLEAR the DTCs. RETRIEVE the DTCs. If DTC B2477 is retrieved again, INSTALL a new module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . REPEAT the self-test. |
| C1095 | ABS Hydraulic Pump Motor Circuit Failure | ABS Module | GO to PINPOINT TEST D . |
| C1096 | ABS Hydraulic Pump Motor Circuit Open | ABS Module | GO to PINPOINT TEST D . |
| C1115 | ABS Power Relay Output Short Circuit To Battery | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1115 is retrieved again, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1145 | Wheel Speed Sensor RF Input Circuit Failure | ABS Module | GO to PINPOINT TEST E . |
| C1155 | Wheel Speed Sensor LF Input Circuit Failure | ABS Module | GO to PINPOINT TEST E . |
| C1165 | Wheel Speed Sensor RR Input Circuit Failure | ABS Module | GO to PINPOINT TEST E . |
| C1175 | Wheel Speed Sensor LR Input Circuit Failure | ABS Module | GO to PINPOINT TEST E . |
| C1185 | ABS Power Relay Output Circuit Failure | ABS Module | CLEAR all DTCs. If DTC C1185 is retrieved again, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1194 | ABS outlet valve coil LF circuit failure | Anti-Lock Brake Control Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1194 is retrieved again, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1198 | ABS Inlet Valve Coil LF Circuit Failure | Anti-Lock Brake Control Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1210 | ABS Outlet Valve Coil RF Circuit Failure | Anti-Lock Brake Control Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1214 | ABS Inlet Valve Coil RF Circuit Failure | Anti-Lock Brake Control Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1222 | Speed Wheel Mismatch | ABS Module | GO to PINPOINT TEST F . |
| C1233 | Wheel Speed LF Input Signal Missing | ABS Module | GO to PINPOINT TEST F . |
| C1234 | Wheel Speed RF Input Signal Missing | ABS Module | GO to PINPOINT TEST F . |
| C1235 | Wheel Speed RR Input Signal Missing | ABS Module | GO to PINPOINT TEST F . |
| C1236 | Wheel Speed LR Input Signal Missing | ABS Module | GO to PINPOINT TEST F . |
| C1242 | ABS Outlet Valve Coil LR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1246 | ABS Outlet Valve Coil RR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1250 | ABS Inlet Valve Coil LR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1254 | ABS Inlet Valve Coil RR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1277 | Steering Wheel Angle 1 and 2 Circuit Failure | ABS Module | GO to PINPOINT TEST G . |
| C1278 | Steering Wheel Angle 1 and 2 Signal Faulted | ABS Module | GO to PINPOINT TEST G . |
| C1279 | Yaw Rate Sensor Circuit Failure | ABS Module | GO to PINPOINT TEST H . |
| C1280 | Yaw Rate Sensor Signal Fault | ABS Module | GO to PINPOINT TEST H . |
| C1281 | Lateral Accelerometer Circuit Failure | ABS Module | GO to PINPOINT TEST H . |
| C1282 | Lateral Accelerometer Signal Fault | ABS Module | GO to PINPOINT TEST H . |
| C1285 | Booster Solenoid Circuit Failure | ABS Module | GO to PINPOINT TEST I . |
| C1286 | Booster Mechanical Failure | ABS Module | GO to PINPOINT TEST I . |
| C1287 | Booster Pedal Force Switch Circuit Failure | ABS Module | GO to PINPOINT TEST J . |
| C1288 | Brake Pressure Transducer Main/Primary Input Circuit Failure | ABS module | GO to PINPOINT TEST B . |
| C1404 | Traction Control Valve Rear Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1410 | Traction Control Valve LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1446 | Brake Switch Circuit Failure | ABS Module | GO to PINPOINT TEST P . |
| C1730 | Reference Voltage Out of Range (+5 V) | ABS Module | If any other DTC(s) are present, diagnose those DTC(s) first. CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, GO to PINPOINT TEST Q . |
| C1957 | Stability Assist Control Valve RF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1958 | Stability Assist Control Valve LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1963 | Stability Control Inhibit Warning | ABS Module | This DTC is for information only. CLEAR all DTCs. |
| C1991 | Module Calibration Failure | ABS Module | GO to PINPOINT TEST M . |
| U1009 | SCP (J1850) Invalid Or Missing Data For Engine Torque | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1011 | SCP (J1850) Invalid Or Missing Data For Engine Air Intake | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1027 | SCP (J1850) Invalid Or Missing Data For Engine Rpm | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1042 | SCP (J1850) Invalid Or Missing Data For Traction Control | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1050 | SCP (J1850) Invalid Or Missing Data For Brakes | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1051 | SCP (J1850) Invalid Or Missing Data For Brakes | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1059 | SCP (J1850) Invalid Or Missing Data For Transmission/Transaxle/PRNDL | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1073 | SCP (J1850) Invalid Or Missing Data For Engine Coolant | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1243 | SCP (J1850) Invalid Or Missing Data For Exterior Environment | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1249 | SCP (J1850) Invalid Or Missing Data For Time/Date | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1262 | SCP (J1850) Communication Bus Fault | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK . |