Section 2 (Intake Air System, Fuel Charging System & Engine Electronics System-4.6L (2V) Engine)

• Specifications
  • General Specifications
  • Torque Specifications
• Description And Operation
  • Intake Air
  • Fuel Charging and Controls
  • Engine Ignition
  • Starting System
  • Electronic Engine Controls
• Diagnosis And Testing
  • Intake Air Distribution and Filtering
  • Fuel Charging and Controls
  • Starting System
    • Notes
    • Special Tool(s)
    • Inspection and Verification
    • Symptom Chart
    • Connector Reference and Terminal Readings
      • Ignition Switch-C250
      • Starter Relay-C1017
      • Passive Anti-Theft (PATS)-C2007
      • Digital Transmission Range (DTR) Sensor-C167
    • Pinpoint Tests
      • Normal Operation
      • Possible Causes
      • Pinpoint Test A: The Engine Does Not Crank Or Relay Clicks
      • Pinpoint Test B: Unusual Starter Noise
    • Component Tests
      • Starter Motor-Voltage Drop Test
      • Starter Motor - Motor Feed Circuit
      • Starter Motor - Motor Ground Circuit
  • Engine Ignition
  • Electronic Engine Controls
• Removal And Installation
  • Air Cleaner Assembly
    • Removal and Installation
    • Item 4: Air Cleaner Outlet Tube Removal Note
    • Item 2: Air Cleaner Outlet Tube Screw Clamp Installation Note
  • Throttle Body
    • Removal and Installation
    • Item 3: Throttle Body Bolt Installation Note
  • Fuel Injection Supply Manifold And Fuel Injector
    • Special Tool(s)
    • Material
    • Removal and Installation
    • Item 1: Fuel Tube Spring Lock Coupling Removal Note
    • Item 20: Fuel Injection Supply Manifold Stud/Bolt Removal Note
    • Item 23: O-Ring Seal Removal Note
    • Item 23: O-Ring Seal Installation Note
    • Item 1: Fuel Tube Spring Lock Coupling Installation Note
  • Fuel Pulse Damper
    • Material
    • Item 3: Fuel Pulse Damper O-ring Installation Note
  • Fuel Pressure And Temperature Sensor
    • Material
  • Starter Motor
  • Ignition Coil-On-Plug And Spark Plug
    • Material
    • Item 4: Spark Plug Removal Note
    • Item 4: Spark Plug Installation Note
    • Item 3: Ignition Coil-On-Plug Installation Note
  • Camshaft Position (CMP) Sensor
    • Special Tool(s)
    • Item 1: Power Steering Pump Pulley Removal Note
    • Item 2: Power Steering Pump Stud Bolts Removal Note
    • Item 3: Power Steering Pump Bolt Removal Note
    • Item 4: Power Steering Pump Removal Note
    • Item 5: Power Steering Reservoir Bracket Nut Removal Note
    • Item 6: Power Steering Reservoir Bracket Removal Note
    • Item 5: Power Steering Reservoir Bracket Nut Installation Note
    • Item 3: Power Steering Pump Bolt Installation Note
    • Item 2: Power Steering Pump Stud Bolts Installation Note
    • Item 1: Power Steering Pump Pulley Installation Note
  • Crankshaft Position (CKP) Sensor
    • Notes
    • Item 3: A/C Compressor Bolt Removal Note
  • Powertrain Control Module (PCM)
    • Notes
    • Item 3: A-Pillar Lower Trim Panel Removal Note
    • Item 7: PCM and Mounting Bracket Removal Note
    • Item 7: PCM and Mounting Bracket Installation Note
  • Mass Air Flow (MAF) Sensor
  • Heated Oxygen Sensor (HO2S) And Catalyst Monitor Sensor
    • Special Tool(s)
    • Material
    • Item 2: Catalyst Monitor Sensor Removal Note
    • Item 3: Heated Oxygen Sensor Removal Note
    • Item 3: Heated Oxygen Sensor Installation Note
    • Item 2: Catalyst Monitor Sensor Installation Note
  • Knock Sensor (KS)
  • Cylinder Head Temperature (CHT) Sensor