Specifications Index
SABLE & TAURUS SPECIFICATIONS INDEX
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | GENERAL SPECIFICATIONS | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Axle Nut/Hub Nut | ||||
| Front | TORQUE SPECIFICATIONS | |||
| Battery | TORQUE SPECIFICATIONS | |||
| Brakes | ||||
| Bleeding Sequence | BRAKE SYSTEM BLEEDING | |||
| Disc Brakes | GENERAL SPECIFICATIONS | |||
| Drum Brakes | GENERAL SPECIFICATIONS | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Charging | ||||
| Generator | GENERAL SPECIFICATIONS | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Drive Belts | ||||
| Adjustment | COMPONENT TESTS | |||
| Belt Routing | ACCESSORY DRIVE | |||
| Engine Cooling | ||||
| General Service Specifications | GENERAL SPECIFICATIONS | |||
| Radiator Cap Pressure | 13-18 psi (89-124 kPa) | |||
| Thermostat R & I | ||||
| 3.0L (2V) | THERMOSTAT - 3.0L (2V) | |||
| 3.0L (4V) | THERMOSTAT - 3.0L (4V) | |||
| Water Pump R & I | ||||
| 3.0L (2V) | WATER PUMP - 3.0L (2V) | |||
| 3.0L (4V) | WATER PUMP - 3.0L (4V) | |||
| Engine Mechanical | ||||
| 3.0L (2V) | ||||
| Compression | COMPRESSION TEST-COMPRESSION GAUGE CHECK | |||
| Oil pressure (Hot 2,500 rpm) | 40-60 psi (276-414 kPa) | |||
| Overhaul | GENERAL SPECIFICATIONS | |||
| Torque | TORQUE SPECIFICATIONS | |||
| 3.0L (4V) | ||||
| Compression | COMPRESSION TEST-COMPRESSION GAUGE CHECK | |||
| Oil pressure (minimum at 1,500 rpm with engine warmed up after 10 minutes of idling.) | 11 psi (76 kPa) | |||
| Overhaul | GENERAL SPECIFICATIONS | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate Torque | 80 Nm (59 Ib-ft) | |||
| Fuel System | ||||
| Fuel Filter Location | Under vehicle, next to fuel pump electrical connector, mounted in clamp. | |||
| Fuel Filter R & I | REMOVAL AND INSTALLATION | |||
| Pressure Release Procedure | ||||
| 3.0L (2V) | FUEL SYSTEM PRESSURE RELEASE -3.0L (2V) | |||
| 3.0L (4V) | FUEL SYSTEM PRESSURE RELEASE - 3.0L (4V) | |||
| Pressure Specification | FUEL SYSTEM SPECIFICATIONS | |||
| Fuel Pressure Test Procedure | A: No Start STEP A10 CHECK THE FUEL PRESSURE | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | ||||
| 3.0L (2V) | FIRING ORDER & CYLINDER IDENTIFICATION | |||
| 3.0L (4V) | FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Ignition Coil (Cylinder Identification) | ||||
| 3.0L (2V) | COIL PACK | |||
| 3.0L (4V) | Coil on plug | |||
| Ignition Wires (Routing) | ||||
| 3.0L (2V) | N/A | |||
| 3.0L (4V) | Coil on plug | |||
| Spark Plug | ||||
| 3.0L (2V) | ||||
| Type | ||||
| Gasoline | Original spark plug: Motorcraft AGSF-32PM and PGM Service spark plug: Motorcraft AGSF-32FM |
|||
| Flex Fuel | Original spark plug: Motorcraft AGSF-22PM/AGSF-22PGM Service spark plug: Motorcraft AGSF-22FM |
|||
| Gap | .042-.046 In. (1.07-1.17 mm) | |||
| Torque | 11 Ft. Lbs. (15 N.m) | |||
| 3.0L (4V) | ||||
| Type | Motorcraft AGSF-32FM | |||
| Gap | .054 In. (1.37 mm) | |||
| Torque | 11 Ft. Lbs. (15 N.m) | |||
| Starting | ||||
| Starter | GENERAL SPECIFICATIONS | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Wheel Alignment | ||||
| Adjustment Specifications | ALIGNMENT SPECIFICATIONS | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 95 Ft. Lbs. (129 N.m) NOTE: Torque specifications are for clean, dry bolt and nut threads. Never use oil or grease on wheel bolts or nuts. |
|||