LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2006 >> Taurus SE, 3.0 U >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission >> Disassembly And Assembly Of Subassemblies >> Pump Assembly >> Disassembly
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Pump Assembly: Disassembly

  1. Remove the valve body separator plate bolts.
    Fig 1: Locating Valve Body Separator Plate Bolts
    G04710087Courtesy of FORD MOTOR CO.
  2. Remove the valve body separator plates and gaskets.
    Fig 2: Locating Valve Body Separator Plates And Gaskets
    G04710088Courtesy of FORD MOTOR CO.
  3. Remove the B8 check ball and note the location.
    Fig 3: Locating Check Ball
    G04710089Courtesy of FORD MOTOR CO.
  4. Remove the 2 bolts.
    Fig 4: Locating Bolts
    G04710090Courtesy of FORD MOTOR CO.
  5. Remove the 2 pump cover bolts.
    Fig 5: Locating Pump Cover Bolts
    G04710091Courtesy of FORD MOTOR CO.
    6. WARNING: Use extreme caution when removing spring to prevent personal injury.
    CAUTION: Place a piece of cardboard or a suitable material under a screwdriver to prevent damage to the housing gasket surface.
    Fig 6: Locating Bore Ring Spring
    G04710092Courtesy of FORD MOTOR CO.
  6. Remove the bore ring spring.
  7. Remove the pump bore ring pin.
    Fig 7: Locating Pump Bore Ring Pin
    G04710093Courtesy of FORD MOTOR CO.
  8. Remove the metal bore ring and support seal.
    1. Remove the bore ring side seal (metal).
    2. Remove the support seal (O-ring).
    Fig 8: Locating Bore Ring Side Seal
    G04710094Courtesy of FORD MOTOR CO.
  9. Remove the pump bore ring radial seal and support.
    1. Remove the pump bore ring radial seal (orange rectangular).
    2. Remove the pump bore ring radial seal support (black round).
    Fig 9: Identifying Pump Bore Ring Radial Seal Support
    G04710095Courtesy of FORD MOTOR CO.
  10. Remove the top pump vane support ring.
    Fig 10: Locating Top Pump Vane Support Ring
    G04710096Courtesy of FORD MOTOR CO.
  11. Remove the outer pump bore ring.
    Fig 11: Locating Outer Pump Bore Ring
    G04710097Courtesy of FORD MOTOR CO.
  12. Remove the vanes.
    Fig 12: Locating Pump Vanes
    G04710098Courtesy of FORD MOTOR CO.
  13. Remove the rotor.
    Fig 13: Locating Rotor
    G04710099Courtesy of FORD MOTOR CO.
  14. Remove the bottom pump vane support ring.
    Fig 14: Locating Bottom Pump Vane Support Ring
    G04710100Courtesy of FORD MOTOR CO.
  15. Remove the EPC, TCC solenoids and seals.
    • Remove the bolts.
    • Remove the EPC, TCC solenoids.
    Fig 15: Locating EPC, TCC Solenoids
    G04710101Courtesy of FORD MOTOR CO.
    16. NOTE: The shift solenoids are interchangeable. Take note of the shift solenoid connector orientation.
    Fig 16: Locating Shift Solenoids Locking Tab
    G04710102Courtesy of FORD MOTOR CO.
  16. Remove the shift solenoids by pressing locking tab with a screwdriver and rotating them.
  17. Inspect the fluid pump body bearing for wear or damage.
    18. CAUTION: The machined passage surfaces of the pump body must be protected when removing the damaged bearing.
    CAUTION: Do not press with excessive force when removing the damaged bearing.
    Fig 17: Removing Bearing Using Special Tool (307-394)
    G04710103Courtesy of FORD MOTOR CO.
  18. If required, use the special tool and a suitable press to remove the bearing assembly.
scientia non olet · About LEMON Manuals