Supplemental Restraints Systems DTCS

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSTIC TROUBLE CODE (DTC) LIST

DTC	Description	Retrieved From	Perform Test
Continuous Lamp	The Air Bag Indicator is Illuminated Continuously (RCM Disconnected or Inoperative, Loss of Battery Feed or Loss of Signal Ground)	RCM	Go to Pinpoint Test A .
B1118	Passenger Front Crash Sensor Mount/Communication Fault	RCM	Go to Pinpoint Test B .
B1135	Passenger Front Crash Sensor Internal Fault	RCM	INSTALL a new RH front impact severity sensor. REFER to Front Impact Severity Sensor in this article.
B1231	Event Threshold Exceeded (Crash Data Memory Full)	RCM	Install new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment in this article.
B1231	Event Threshold Exceeded (Crash Data Memory Full)	OCS module	Install a new OCS service kit and CLEAR all RCM and OCS module DTCs. REFER to Occupant Classification Sensor and Inspection and Repair After a Supplemental Restraint System (SRS) Deployment in this article.
B1317	Battery Voltage High	RCM	CHECK battery voltage; to be below 18 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION article.
B1317	Battery Voltage High	OCS module	NOTE: If no on-demand or continuous DTC is present in the RCM and DTC B1317 is only present in the OCS module continuous, CLEAR all OCS module DTCs and PROVE OUT the system. CHECK battery voltage; to be below 18 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION article.
B1318	Battery Voltage Low	RCM	CHECK battery voltage; to be above 8 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION article.
B1318	Battery Voltage Low	OCS module	NOTE: If no on-demand or continuous DTC is present in the RCM and DTC B1318 is only present in the OCS module continuous, CLEAR all OCS module DTCs and PROVE OUT the system. CHECK battery voltage; to be above 8 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION article.
B1342	ECU (RCM) is Faulted	RCM	INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this article.
B1342	ECU (OCS module) is Faulted	OCS module	INSTALL a new OCS service kit. REFER to Occupant Classification Sensor in this article.
B1884	PAD Warning Lamp Circuit Failure	RCM	Go to Pinpoint Test C .
B1890	PAD Warning Lamp Circuit Short to Battery	RCM	Go to Pinpoint Test D .
B2290	Occupant Classification System Fault	RCM	NOTE: If no on-demand or continuous DTC is present in the OCS module and DTC B2290 is only present in the RCM as a continuous DTC, CLEAR all RCM DTCs and PROVE OUT the system. The OCS module reported a fault message to the RCM. CARRY OUT on-demand self test of the OCS module and RETRIEVE continuous DTCs.
B2290	Occupant Classification System Fault	OCS module	NOTE: If no on-demand or continuous DTC is present in the OCS module and DTC B2290 is only present in the RCM as a continuous DTC, CLEAR all RCM DTCs and PROVE OUT the system. Go to Pinpoint Test E .
B2292	Restraint System - Seatbelt Pretensioner Fault (Driver Pretensioner Circuit Fault)	RCM	Go to Pinpoint Test F .
B2292	Restraint System - Seatbelt Pretensioner Fault (Passenger Pretensioner Circuit Fault)	RCM	Go to Pinpoint Test F .
B2293	Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault)	RCM	Go to Pinpoint Test G .
B2293	Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault)	RCM	Go to Pinpoint Test G .
B2296	Restraint System - Impact Sensor Fault (Driver Front Impact Severity Sensor Circuit Fault)	RCM	Go to Pinpoint Test H .
B2434	Drivers Seat Belt Buckle Switch Circuit Short to Ground	RCM	Go to Pinpoint Test I .
B2435	Drivers Seat Belt Buckle Switch Resistance Out of Range	RCM	Go to Pinpoint Test J .
B2438	Passenger Seat Belt Buckle Switch Short to Ground	RCM	Go to Pinpoint Test K .
B2439	Passenger Seat Belt Buckle Switch Resistance Out of Range	RCM	Go to Pinpoint Test L .
B2477	Module Configuration Failure	RCM	INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this article.
B2477	Module Configuration Failure	OCS module	INSTALL a new OCS module. REFER to Occupant Classification Sensor in this article.
B2607	Harness/Configuration Mismatch	RCM	INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this article.
B2691	Seat Belt Buckle Switch Circuit Fault, Front Driver's Side	RCM	Go to Pinpoint Test M .
B2692	Front Passenger's Seat Belt Buckle Switch Circuit Fault	RCM	Go to Pinpoint Test N .
B2792	Cross Link Between Firing Loops (This DTC and the Associated Firing Loops That are Crossed Will Set Applicable Loop Fault With Low Resistance on Squib)	RCM	Go to Pinpoint Test O .
C1414	Incorrect Module Design Level (Incorrect Vehicle Application)	RCM	INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this article.
C1941	Zero Seat Weight Test Failure	OCS module	Can only be reported when carrying out Occupant Classification Sensor (OCS) System Reset. REFER to Occupant Classification Sensor in this article.
B2909	Belt Tension Sensor Fault	OCS module	Go to Pinpoint Test P .
C1946	Front Driver's Seat Track Position Switch Circuit Open	RCM	Go to Pinpoint Test Q .
C1947	Front Driver's Seat Track Position Switch Circuit Short to Ground	RCM	Go to Pinpoint Test R .
C1948	Front Driver's Seat Track Position Switch Circuit Resistance Out of Range	RCM	Go to Pinpoint Test S .
C1981	Front Driver's Seat Track Position Switch Circuit Fault	RCM	Go to Pinpoint Test T .
U0300	Internal Control Module Software Incompatibility	RCM	INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this article.
U1900	CAN Communication Bus Fault - Receive Error	RCM	Go to Pinpoint Test U .
U1900	CAN Communication Bus Fault - Receive Error	OCS module	NOTE: If no on-demand or continuous DTC is present in the RCM and DTC U1900 is only present in the OCS module continuous, CLEAR all OCS module DTCs and PROVE OUT the system. Go to Pinpoint Test V .
U0151	Loss of Communication With Restraints Control Module	OCS	REFER to MODULE COMMUNICATIONS NETWORK article.
U2050	No Application Present	RCM	INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this article.
U2050	No Application Present	OCS module	NOTE: If no on-demand or continuous DTC is present in the RCM and DTC U2050 is only present in the OCS module continuous, CLEAR all OCS module DTCs and PROVE OUT the system. INSTALL a new OCS service kit. REFER to Occupant Classification Sensor in this article.
U2051	One or More Calibration Files Missing/Corrupt	RCM	INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this article.
U2051	One or More Calibration Files Missing/Corrupt	OCS module	INSTALL a new OCS service kit. REFER to Occupant Classification Sensor in this article.