Audio Control Module (ACM) - With Navigation DTC Chart
DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B119F:01 | GPS Antenna: General Electrical Failure | GO to PINPOINT TEST N . |
| B119F:13 | GPS Antenna: Circuit Open | GO to PINPOINT TEST N . |
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage Out of Range | GO to PINPOINT TEST F . |
| B113BA:63 | Steering Wheel Audio Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST F . |
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to PINPOINT TEST F . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit/Component Protection Time-Out | GO to PINPOINT TEST F . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1A01:01 | Speaker #1: General Electrical Failure | GO to PINPOINT TEST P . |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to PINPOINT TEST P . |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST P . |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to PINPOINT TEST P . |
| B1A05:01 | Speaker #5: General Electrical Failure | GO to PINPOINT TEST D . |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | GO to PINPOINT TEST A . |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST M . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST M . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| B1D19:4B | Compact Disc Unit: Over Temperature | ALLOW the ACM to cool for 30 minutes. CLEAR the DTCs. This is normal operation. |
| B1D78:13 | Auxiliary Input: Circuit Open | GO to PINPOINT TEST H . |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to PINPOINT TEST T . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AA . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | If the speed sensitive volume is inoperative, GO to PINPOINT TEST G
. If the navigation is inaccurate, GO to PINPOINT TEST O . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to PINPOINT TEST J . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | If only the display is inoperative, GO to PINPOINT TEST J
. If the entire SYNC system is inoperative, GO to PINPOINT TEST V . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST Q . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST S . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AB . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AC . |