LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2009 >> Focus SES, 4D Sedan, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 107 (Module Communications Network) >> Diagnostic Tests >> Communications Network >> Pinpoint Tests >> Pinpoint Test B: The ABS Module Does Not Respond To The Scan Tool
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Pinpoint Test B: The ABS Module Does Not Respond To The Scan Tool

WARNING: This page is about a different car, the 2009 Mercury Grand Marquis and 2009 Ford Crown Victoria. However, it is still accessible from the selected car via links, so may be relevant.

Refer to appropriate SYSTEM WIRING DIAGRAMS article, Module Communications Network for schematic and connector information.

Refer to appropriate SYSTEM WIRING DIAGRAMS article, Vehicle Dynamic Systems for schematic and connector information.

Normal Operation 

The ABS module communicates with the scan tool through the high speed controller area network (HS-CAN). Circuits 1827 (WH/LG) (HS-CAN +) and 1828 (PK/LG) (HS-CAN -) provide the network connection to the ABS module. The ABS module shares the HS-CAN with the PCM, the vehicle dynamics module (VDM) (if equipped), the instrument cluster (IC) and the fire suppression system module (FSSM) (if equipped). Voltage for the ABS module is provided by circuits 483 (RD), 601 (LB/PK) and 1003 (GY/YE) and ground is provided by circuit 57 (BK).

This pinpoint test is intended to diagnose the following:

PINPOINT TEST B: THE ABS MODULE DOES NOT RESPOND TO THE SCAN TOOL 

NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
  1. B1 CHECK THE HS-CAN TERMINATION RESISTANCE 
    • Key in OFF position.
      • NOTE: Failure to disconnect the battery will result in false resistance readings.
    • Disconnect the battery ground cable.
    • Disconnect the scan tool cable from the data link connector (DLC).
      • Fig 1: Measuring Resistance
      GF0004695Courtesy of FORD MOTOR CO.
    • Measure the resistance between the DLC C251-6, circuit 1827 (WH/LG), harness side and the DLC C251-14, circuit 1828 (PK/LG), harness side.
    • Is the resistance between 54 and 66 ohms? 
    1. YES  : Go to  B2.
    2. NO  : Go to  B4.
  2. B2 CHECK THE ABS MODULE VOLTAGE SUPPLY CIRCUITS FOR AN OPEN 
    • Key in OFF position.
    • Disconnect: ABS Module C135
    • Key in ON position.
    • Measure the voltage between the ABS module, harness side and ground as follows:
      Connector-Pin Circuit
      C135-8 1003 (GY/YE)
      C135-13 601 (LB/PK)
      C135-14 483 (RD)
    • Are the voltages greater than 10 volts? 
    1. YES  : Go to  B3.
    2. NO  : VERIFY the battery junction box (BJB) fuse 106 (40A) or fuse 109 (20A) and the central junction box (CJB) fuse 13 (10A) is OK. If OK, REPAIR the circuit in question. CONNECT the ABS module. CLEAR the DTCs. REPEAT the network test with the scan tool.
  3. B3 CHECK THE ABS MODULE GROUND CIRCUITS FOR AN OPEN 
    • Key in OFF position.
      • Fig 2: Checking Circuits For Open
      GF0014022Courtesy of FORD MOTOR CO.
    • Measure the resistance between the ABS module, harness side and ground as follows:
      Connector-Pin Circuit
      C135-12 57 (BK)
      C135-15 57 (BK)
    • Are the resistances less than 5 ohms? 
    1. YES  : Go to  B4.
    2. NO  : REPAIR the circuit in question. CONNECT the ABS module. CLEAR the DTCs. REPEAT the network test with the scan tool.
  4. B4 CHECK THE HS-CAN CIRCUITS BETWEEN THE DATA LINK CONNECTOR (DLC) AND THE ABS MODULE FOR AN OPEN 
      Fig 3: Checking Circuit For Open
      GF0014632Courtesy of FORD MOTOR CO.
    • Measure the resistance between the ABS module C135-18, circuit 1827 (WH/LG), harness side and the DLC C251-6, circuit 1827 (WH/LG), harness side.
      • Fig 4: Checking Circuit For Open
      GF0014633Courtesy of FORD MOTOR CO.
    • Measure the resistance between the ABS module C135-28, circuit 1828 (PK/LG), harness side and the DLC C251-14, circuit 1828 (PK/LG), harness side.
    • Are the resistances less than 5 ohms? 
    1. YES  : Go to  B5.
    2. NO  : REPAIR the circuit in question. CONNECT the ABS module. CLEAR the DTCs. REPEAT the network test with the scan tool.
  5. B5 CHECK FOR CORRECT ABS MODULE OPERATION 
    • Disconnect the ABS module connector.
    • Check for:
      • corrosion
      • damaged pins
      • pushed-out pins
    • Connect the ABS module connector and make sure it seats correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present? 
    1. YES  : INSTALL a new ABS module. REFER to VEHICLE DYNAMIC SYSTEMS article. CLEAR the DTCs. REPEAT the network test with the scan tool.
    2. NO  : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the network test with the scan tool.
scientia non olet · About LEMON Manuals