Vehicle Dynamic Systems
ABS MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Action |
|---|---|---|---|
| B1317 | Battery Voltage High | ABS Module | Go To PINPOINT TEST A . |
| B1318 | Battery Voltage Low | ABS Module | Go To PINPOINT TEST A . |
| B1342 | ECU is Faulted | ABS Module | CLEAR the DTCs. REPEAT the self-test. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . REPEAT the self-test with the brake pedal not applied. |
| B1485 | Brake Pedal Input Circuit Battery Short | ABS Module | Go To PINPOINT TEST E . |
| C1095 | ABS Hydraulic Pump Motor Circuit Failure | ABS Module | Go To PINPOINT TEST D . |
| C1096 | ABS Hydraulic Pump Motor Circuit Open | ABS Module | Go To PINPOINT TEST D . |
| C1145 | RF Wheel Speed Sensor Input Circuit Failure | ABS Module | Go To PINPOINT TEST B . |
| C1148 | RF Wheel Speed Sensor Coherency Fault | ABS Module | Go To PINPOINT TEST C . |
| C1155 | LF Wheel Speed Sensor Input Circuit Failure | ABS Module | Go To PINPOINT TEST B . |
| C1158 | LF Wheel Speed Sensor Coherency Fault | ABS Module | Go To PINPOINT TEST C . |
| C1186 | ABS Power Relay Output Open Circuit | ABS Module | Go To PINPOINT TEST A . |
| C1187 | Brake Fluid Level Sensor Input Circuit Open | ABS Module | Go To PINPOINT TEST G . |
| C1194 | ABS Outlet Valve Coil LF Circuit Failure | ABS Module | CLEAR all DTCs. REPEAT the self-test. If DTC C1194 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1198 | ABS Inlet Valve Coil LF Circuit Failure | ABS Module | CLEAR all DTCs. REPEAT the self-test. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1210 | ABS Outlet Valve Coil RF Circuit Failure | ABS Module | CLEAR all DTCs. REPEAT the self-test. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1214 | ABS Inlet Valve Coil RF Circuit Failure | ABS Module | CLEAR all DTCs. REPEAT the self-test. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1229 | Rear Wheel Speed Sensor Coherency Fault | ABS Module | Go To PINPOINT TEST C . |
| C1230 | Rear Wheel Speed Sensor Input Circuit Failure | ABS Module | Go To PINPOINT TEST B . |
| C1233 | LF Wheel Speed Sensor Signal Incorrect | ABS Module | Go To PINPOINT TEST C . |
| C1234 | RF Wheel Speed Sensor Signal Incorrect | ABS Module | Go To PINPOINT TEST C . |
| C1237 | Rear Wheel Speed Sensor Signal Incorrect | ABS Module | Go To PINPOINT TEST C . |
| C1246 | ABS Outlet Valve Coil Rear Circuit Failure | ABS Module | CLEAR all DTCs. REPEAT the self-test. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1254 | ABS Inlet Valve Coil Rear Circuit Failure | ABS Module | CLEAR all DTCs. REPEAT the self-test. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1266 | ABS Valve Power Relay Circuit Failure | ABS Module | CLEAR all DTCs. REPEAT the self-test. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE and CARRY OUT the self-test with the brake pedal not applied. |
| C1414 | Incorrect Module Design Level | ABS Module | Go To PINPOINT TEST F . |
| C1949 | G-Sensor Circuit Open | ABS Module |
NOTE:
DTC C1949 applies only to Four-Wheel Drive (4WD) vehicles. CLEAR all DTCs. REPEAT the self-test. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE
and CARRY OUT the self-test with the brake pedal not applied. |
| C1950 | G-Sensor Signal Failure | ABS Module |
NOTE:
DTC C1950 applies only to 4WD vehicles. CYCLE the ignition switch from OFF to RUN. CLEAR the DTCs. DRIVE the vehicle for at least one minute at speeds greater than 10 km/h (6 mph). REPEAT the self-test with the brake pedal not applied.If DTC C1950 returns, CHECK the HCU
mounting bracket, bolts and ABS module for correct installation.If the installation is correct, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE
. CYCLE the ignition switch from OFF to RUN, CLEAR the DTCs and DRIVE the vehicle at least 10 km/h (6 mph) for at least 3 minutes. |