LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2011 >> Edge SE, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1657 (Supplemental Restraint System) >> General Procedures >> Occupant Classification Sensor (OCS) System Reset >> Special Tool(s)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Special Tool(s)

WARNING: This page is about a different car, the 2010 Lincoln MKX and 2010 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.
SPECIAL TOOL(S) SPECIFICATION

G06064936Courtesy of FORD MOTOR CO.
 Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) software with appropriate hardware, or equivalent scan tool
WARNING: The following precautions must be taken before carrying out the following procedure on the front passenger seat:
  • Park the vehicle on level ground.
  • Make sure the occupant classification sensor (OCS) system is stabilized at a temperature in the range of 5°C to 48°C (41°F to 118°F) and is not exposed to temperatures outside that range.
  • Make sure the front passenger seat is empty and dry.
  • Make sure the front passenger seat repair is complete and all attached components (head restraint, seat side shield) are correctly installed.
  • Make sure nothing is placed in the map pockets (if equipped) of the front passenger seat.
  • Make sure nothing is underneath the front passenger seat.
  • Make sure no non-factory installed items (seat covers, DVD screens) are on or contacting the front passenger seat. If any non-factory items were installed to the seat, remove the item(s) and communicate to the customer that any alteration/modification to the front passenger seat may affect performance of the OCS  system. Refer to the Owner's Literature.
  • Make sure the seat is correctly installed in the vehicle.

Failure to follow these instructions may result in incorrect operation of the OCS  system and increases the risk of serious personal injury or death in a crash.

After Deployment 

NOTE: After installation of new Occupant Classification Sensor (OCS) system components and completion of INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT , the Occupant Classification System Module (OCSM) will have DTCs stored in memory. These DTCs will clear after a successful System Reset.
  1. Check that all steps have been carried out as outlined in the INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT  procedure.
  2. If no concerns are found, proceed to Step  4to carry out the System Reset  .

    No Deployment 

    NOTE: After installation of new OCS  system components (OCS  weight sensor bolt(s), seat track assembly or OCSM  ), the OCSM  will have DTCs stored in memory. These DTCs will clear after a successful System Reset.
  3. Carry out the Restraints Control Module (RCM) self-test. If DTC B2290 is retrieved on-demand, check the OCSM  for DTCs.
    • If DTCs are retrieved on-demand in the OCSM  and NO  new components have been installed, refer to the OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) DTC CHART  for diagnostic direction.
    • If no DTCs are retrieved on-demand in the OCSM  , CLEAR the DTC from the RCM  and carry out the System Reset.

    OCS System Reset 

  4. Turn the ignition to the OFF position.
  5. Prepare the passenger seat for a System Reset and make sure:
    • the OCS  weight sensor bolt harness connections are correct for each sensor at the correct locations. Refer to SYSTEM WIRING DIAGRAMS for Edge or SYSTEM WIRING DIAGRAMS for MKX for schematic and connector information. Refer to the illustration for correct sensor location on the seat.
    • the seat wiring harnesses are routed and secured correctly and are not twisted, pinched, pulling down or pushing up on any seat component. Refer to Seat Wire Harness Routing in GENERAL PROCEDURES .
    • all seat fasteners have been tightened to specification as identified in the Service Information. Refer to SPECIFICATIONS .
    • the seat track is correctly aligned (manual seat track).
    • the seat is correctly installed in the vehicle.
    • the passenger safety belt buckle is unbuckled.
    • the front passenger seat is empty and there is nothing underneath the seat. Remove any items from the seat that were not factory installed and make sure that the seat is correctly installed in the vehicle.
    • the seat backrest is in the upright (vertical) position.
    • the seat is at the mid-point of the seat track travel.
    • the seat height is in its middle position (power seat only).
    • the hysteresis has been removed from the front passenger seat by firmly hitting the seat backrest 3 times.
    • the vehicle electrical system voltage is below 18 volts and above 11.5 volts  before continuing with the OCS  System Reset.
      Fig 1: Identifying OCS Weight Sensor Bolt Location
      G06174117Courtesy of FORD MOTOR CO.
  6. Turn the ignition ON, wait 8 seconds  .
  7. Carry out the OCS  System Reset
    8. NOTE: Do not install any new OCS  system components at this time. OCS  system components should only be installed when directed to do so.
  8. Carry out the OCSM  self-test.
    • If DTC B00A0:54 is retrieved on-demand, refer to the DTC CHARTS  for diagnostic direction of this DTC.
    • If any other DTC are retrieved on-demand from the OCSM  , proceed to Step 9  .
  9. Inspect all the items listed in Step  5 for causes of a unsuccessful System Reset, repair as necessary. Retest the system  .
  10. If the System Reset was successful, carry out the OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM ZERO SEAT WEIGHT TEST .

    If the System Reset was unsuccessful, install a new passenger seat track assembly. For additional information, refer to REMOVAL AND INSTALLATION .

scientia non olet · About LEMON Manuals