ABS Module

ABS MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST

DTC	Description	Action
B1317	Battery Voltage High	Go to PINPOINT TEST A .
B1318	Battery Voltage Low	Go to PINPOINT TEST A .
B1342	ECU is Faulted	NOTE: If other DTCs are present, REPAIR them before installing a new component. CLEAR the DTCs. Carry Out the ABS module self-test. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. Carry Out the self-test with the brake pedal not applied.
B2477	Module Configuration Failure	CONFIGURE the ABS module. Refer to MODULE CONFIGURATION . CLEAR the DTCs. REPEAT the self-test. If DTC B2477 is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. REPEAT the self-test.
B2900	VIN Mismatch	Go to PINPOINT TEST S .
C1095	ABS Hydraulic Pump Motor Circuit Failure	Go to PINPOINT TEST C .
C1096	ABS Hydraulic Pump Motor Circuit Open	Go to PINPOINT TEST C .
C110A	ABS Active Circuit Short to Battery	If any other DTCs are present (except B1342), diagnose those DTCs first. This DTC is used for aftermarket equipment (like an engine braking device) and indicates that there is a concern in the aftermarket equipment. When in use, this circuit (pin-31 of the ABS module electrical connector) informs the aftermarket equipment that an ABS event is in progress. If the vehicle is equipped with aftermarket equipment, VERIFY that those systems are functioning correctly. ISOLATE the aftermarket equipment and Carry Out the ABS module self-test. If the DTC does not return, the concern is in the aftermarket equipment. If the DTC returns or if the vehicle is not equipped with any aftermarket equipment, DISCONNECT the ABS module electrical connector and INSPECT the connector for corrosion, water intrusion and other contamination. If contamination is present, CLEAN or REPAIR the connector as necessary. CLEAR the DTC. REPEAT the self-test. If no contamination is present, CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information.
C1115	ABS Power Relay Output Short Circuit to Battery	NOTE: If other DTCs are present, REPAIR them before installing a new component. CLEAR all DTCs. TEST DRIVE the vehicle above 32 km/h (20 mph) and Carry Out at least one ABS stop. RETRIEVE the DTCs.If DTC C1115 is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. Carry Out the self-test with the brake pedal not applied.
C1145	RF Wheel Speed Sensor Input Circuit Failure	Go to PINPOINT TEST D .
C1155	LF Wheel Speed Sensor Input Circuit Failure	Go to PINPOINT TEST D .
C1185	ABS Power Relay Output Circuit Failure	NOTE: If other DTCs are present, REPAIR them before installing a new component. CLEAR all DTCs. RETRIEVE DTCs. If DTC C1185 is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. Carry Out the self-test with the brake pedal not applied.
C1194	ABS Outlet Valve Coil LF Circuit Failure	Go to PINPOINT TEST B .
C1198	ABS Inlet Valve Coil LF Circuit Failure	Go to PINPOINT TEST B .
C1210	ABS Outlet Valve Coil RF Circuit Failure	Go to PINPOINT TEST B .
C1214	ABS Inlet Valve Coil RF Circuit Failure	Go to PINPOINT TEST B .
C1222	Wheel Speed Mismatch	NOTE: If DTCs C1233 and/or C1234 are present, diagnose those DTCs before diagnosing C1222. Go to PINPOINT TEST F .
C1233	LF Wheel Speed Input Signal Missing	Go to PINPOINT TEST E .
C1234	RF Wheel Speed Input Signal Missing	Go to PINPOINT TEST E .
C1237	Rear Wheel Speed Input Signal Missing	Go to PINPOINT TEST F .
C1242	ABS Outlet Valve Coil LR Circuit Failure	Go to PINPOINT TEST B .
C1246	ABS Outlet Valve Coil RR Circuit Failure	Go to PINPOINT TEST B .
C1250	ABS Inlet Valve Coil LR Circuit Failure	Go to PINPOINT TEST B .
C1329	ABS Outlet Valve Coil RF Circuit Excessive Temperature	CLEAR all DTCs. TEST DRIVE the vehicle above 32 km/h (20 mph) and Carry Out at least one ABS stop. RETRIEVE the DTCs. If the DTC is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. Carry Out the self-test with the brake pedal not applied.
C1330	ABS Outlet Valve Coil LR Circuit Excessive Temperature	CLEAR all DTCs. TEST DRIVE the vehicle above 32 km/h (20 mph) and Carry Out at least one ABS stop. RETRIEVE the DTCs. If the DTC is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. Carry Out the self-test with the brake pedal not applied.
C1331	ABS Outlet Valve Coil RR Circuit Excessive Temperature	CLEAR all DTCs. TEST DRIVE the vehicle above 32 km/h (20 mph) and CARRY OUT at least one ABS stop. RETRIEVE the DTCs. If the DTC is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. CARRY OUT the self-test with the brake pedal not applied.
C1332	ABS Outlet Valve Coil LF Circuit Excessive Temperature	CLEAR all DTCs. TEST DRIVE the vehicle above 32 km/h (20 mph) and CARRY OUT at least one ABS stop. RETRIEVE the DTCs. If the DTC is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. CARRY OUT the self-test with the brake pedal not applied.
C1333	ABS Inlet Valve Coil LR Circuit Excessive Temperature	CLEAR all DTCs. TEST DRIVE the vehicle above 32 km/h (20 mph) and CARRY OUT at least one ABS stop. RETRIEVE the DTCs. If the DTC is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. CARRY OUT the self-test with the brake pedal not applied.
C1334	ABS Inlet Valve Coil LF Circuit Excessive Temperature	CLEAR all DTCs. TEST DRIVE the vehicle above 32 km/h (20 mph) and CARRY OUT at least one ABS stop. RETRIEVE the DTCs. If the DTC is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. CARRY OUT the self-test with the brake pedal not applied.
C1335	ABS Inlet Valve Coil RF Circuit Excessive Temperature	CLEAR all DTCs. TEST DRIVE the vehicle above 32 km/h (20 mph) and CARRY OUT at least one ABS stop. RETRIEVE the DTCs. If the DTC is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. CARRY OUT the self-test with the brake pedal not applied.
C1336	ABS Inlet Valve Coil RR Circuit Excessive Temperature	CLEAR all DTCs. TEST DRIVE the vehicle above 32 km/h (20 mph) and CARRY OUT at least one ABS stop. RETRIEVE the DTCs. If the DTC is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTCs. CARRY OUT the self-test with the brake pedal not applied.
C1446	Brake Switch Circuit Failure	Go to PINPOINT TEST G .
U0073	Control Module Communication Bus Off	Refer to MODULE COMMUNICATIONS NETWORK to diagnose the HS-CAN bus.
U0115	Lost Communication with ECM/PCM - Secondary (SPCM)	REPAIR all other DTCs first. If DTC U0115 is still present refer to MODULE COMMUNICATIONS NETWORK to diagnose HS-CAN bus.
U0155	Lost Communication with Instrument Panel Cluster (IC) Control Module	REPAIR all other DTCs first. If DTC U0155 is still present refer to MODULE COMMUNICATIONS NETWORK to diagnose the HS-CAN bus.
U2050	No Application Present	CLEAR the DTC. REPEAT the self-test. RETRIEVE the DTCs. If DTC U2050 is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTC. REPEAT the self-test.
U2051	One or More Calibration Files Missing/Corrupt	CLEAR the DTC. REPEAT the self-test. RETRIEVE the DTCs. If DTC U2051 is retrieved again, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE in this information. CLEAR the DTC. REPEAT the self-test.