Restraints Control Module (RCM)
DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action To Take |
|---|---|---|
| Continuous lamp | The Air Bag Warning Indicator is Illuminated Continuously | Go to PINPOINT TEST A . |
| B0001:11 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground | Go to PINPOINT TEST B . |
| B0001:12 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery | Go to PINPOINT TEST B . |
| B0001:13 | Driver Frontal Stage 1 Deployment Control: Circuit Open | Go to PINPOINT TEST B . |
| B0001:1A | Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | Go to PINPOINT TEST B . |
| B0001:2B | Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled | Go to PINPOINT TEST J . |
| B0001:4A | Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed | Go to PINPOINT TEST K . |
| B0002:11 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the Restraints Control Module (RCM) is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0002:12 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0002:13 | Driver Frontal Stage 2 Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0002:1A | Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0002:2B | Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0002:4A | Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0005:11 | Collapsible Steering Column Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0005:12 | Collapsible Steering Column Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0005:13 | Collapsible Steering Column Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0005:1A | Collapsible Steering Column Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0005:2B | Collapsible Steering Column Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0005:4A | Collapsible Steering Column Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0010:11 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground | Go to PINPOINT TEST C . |
| B0010:12 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery | Go to PINPOINT TEST C . |
| B0010:13 | Passenger Frontal Stage 1 Deployment Control: Circuit Open | Go to PINPOINT TEST C . |
| B0010:1A | Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | Go to PINPOINT TEST C . |
| B0010:2B | Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled | Go to PINPOINT TEST J . |
| B0010:4A | Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed | Go to PINPOINT TEST K . |
| B0021:11 | Left Curtain Deployment Control 1: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0021:12 | Left Curtain Deployment Control 1: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0021:13 | Left Curtain Deployment Control 1: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0021:1A | Left Curtain Deployment Control 1: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0021:2B | Left Curtain Deployment Control 1: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0021:4A | Left Curtain Deployment Control 1: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0050:11 | Driver Seatbelt Sensor: Circuit Short to Ground | Go to PINPOINT TEST D . |
| B0050:12 | Driver Seatbelt Sensor: Circuit Short to Battery | Go to PINPOINT TEST D . |
| B0050:13 | Driver Seatbelt Sensor: Circuit Open | Go to PINPOINT TEST D . |
| B0050:1D | Driver Seatbelt Sensor: Circuit Current Out of Range | Go to PINPOINT TEST D . |
| B0050:2B | Driver Seatbelt Sensor: Signal Cross Coupled | Go to PINPOINT TEST J . |
| B0050:4A | Driver Seatbelt Sensor: Incorrect Component Installed | Go to PINPOINT TEST K . |
| B0080:11 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0080:12 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0080:13 | Driver Seatbelt Load Limiter Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0080:1A | Driver Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0080:2B | Driver Seatbelt Load Limiter Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0080:4A | Driver Seatbelt Load Limiter Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0082:11 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0082:12 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0082:13 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0082:1A | Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0082:2B | Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0082:4A | Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0090:11 | Left Frontal Restraints Sensor: Circuit Short to Ground | Go to PINPOINT TEST E . |
| B0090:4A | Left Frontal Restraints Sensor: Incorrect Component Installed | Go to PINPOINT TEST K . |
| B0090:81 | Left Frontal Restraints Sensor: Invalid Serial Data Received | INSTALL a new LH front impact severity sensor. Refer to FRONT IMPACT SEVERITY SENSOR in this information. |
| B0090:93 | Left Frontal Restraints Sensor: No Operation | Go to PINPOINT TEST E . |
| B0090:96 | Left Side Restraints Sensor 1: Component Internal Failure | INSTALL a new LH front impact severity sensor. Refer to FRONT IMPACT SEVERITY SENSOR in this information. |
| B0095:11 | Right Frontal Restraints Sensor: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0095:4A | Right Frontal Restraints Sensor: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0095:81 | Right Frontal Restraints Sensor: Invalid Serial Data Received |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0095:93 | Right Frontal Restraints Sensor: No Operation |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B0095:96 | Right Frontal Restraints Sensor: Component Internal Failure |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B00A0:09 | Occupant Classification System: Component Failure |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B00A0:4A | Occupant Classification System: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B00A0:63 | Occupant Classification System: Circuit / Component Protection Time-Out |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B00A0:64 | Occupant Classification System: Signal Plausibility Failure |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B00A0:68 | Occupant Classification System: Event Information |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B00D5:11 | Restraint System Passenger Disable Indicator: Circuit Short to Ground | Go to PINPOINT TEST F . |
| B00D5:12 | Restraint System Passenger Disable Indicator: Circuit Short to Battery | Go to PINPOINT TEST F . |
| B00D5:13 | Restraint System Passenger Disable Indicator: Circuit Open | Go to PINPOINT TEST F . |
| B00D5:4A | Restraint System Passenger Disable Indicator: Incorrect Component Installed | Go to PINPOINT TEST K . |
| B00DF:11 | Passenger Restraints Disable Switch: Circuit Short to Ground | Go to PINPOINT TEST G . |
| B00DF:12 | Passenger Restraints Disable Switch: Circuit Short to Battery | Go to PINPOINT TEST G . |
| B00DF:13 | Passenger Restraints Disable Switch: Circuit Open | Go to PINPOINT TEST G . |
| B00DF:1D | Passenger Restraints Disable Switch: Circuit Current Out of Range | Go to PINPOINT TEST G . |
| B00DF:2B | Passenger Restraints Disable Switch: Signal Cross Coupled | Go to PINPOINT TEST J . |
| B00DF:4A | Passenger Restraints Disable Switch: Incorrect Component Installed | Go to PINPOINT TEST K . |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | INSTALL a new RCM and impact sensors. Refer to INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT in this information. |
| B11CD:11 | Driver Frontal Airbag Canister Vent: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B11CD:12 | Driver Frontal Airbag Canister Vent: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B11CD:13 | Driver Frontal Airbag Canister Vent: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B11CD:1A | Driver Frontal Airbag Canister Vent: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B11CD:2B | Driver Frontal Airbag Canister Vent: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B11CD:4A | Driver Frontal Airbag Canister Vent: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM
is incorrectly configured or the incorrect RCM
is installed to the vehicle. INSTALL a new RCM
and carry out Programmable Module Installation (PMI). Use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM)
in this information. |
| B1212:11 | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Short to Ground | Go to PINPOINT TEST H . |
| B1212:12 | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Short to Battery | Go to PINPOINT TEST H . |
| B1212:13 | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Open | Go to PINPOINT TEST H . |
| B1212:1A | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Resistance Below Threshold | Go to PINPOINT TEST H . |
| B1212:2B | Driver Seatbelt Buckle Pretensioner Deployment Control: Signal Cross Coupled | Go to PINPOINT TEST J . |
| B1212:4A | Driver Seatbelt Buckle Pretensioner Deployment Control: Incorrect Component Installed | Go to PINPOINT TEST K . |
| B1213:11 | Passenger Seatbelt Buckle Pretensioner Deployment Control: Circuit Short to Ground | Go to PINPOINT TEST I . |
| B1213:12 | Passenger Seatbelt Buckle Pretensioner Deployment Control: Circuit Short to Battery | Go to PINPOINT TEST I . |
| B1213:13 | Passenger Seatbelt Buckle Pretensioner Deployment Control: Circuit Open | Go to PINPOINT TEST I . |
| B1213:1A | Passenger Seatbelt Buckle Pretensioner Deployment Control: Circuit Resistance Below Threshold | Go to PINPOINT TEST I . |
| B1213:2B | Passenger Seatbelt Buckle Pretensioner Deployment Control: Signal Cross Coupled | Go to PINPOINT TEST J . |
| B1213:4A | Passenger Seatbelt Buckle Pretensioner Deployment Control: Incorrect Component Installed | Go to PINPOINT TEST K . |
| U0028:08 | Vehicle Communication Bus A: Bus Signal / Message Failures | Go to PINPOINT TEST L . |
| U0028:88 | Vehicle Communication Bus A: Bus Off | Go to PINPOINT TEST L . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | Refer to MODULE COMMUNICATIONS NETWORK to diagnose the lost communication with the PCM. |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | Refer to MODULE COMMUNICATIONS NETWORK to diagnose the lost communication with the Instrument Panel Cluster (IPC) module. |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | CHECK for additional RCM and APIM DTCs. Refer to the appropriate information to diagnose the DTCs. If no other DTCs are present, refer to Accessory Protocol Interface Module (APIM) Software Level Check in the General Procedures portion of DRIVER INFORMATION SYSTEM & ENTERTAINMENT SYSTEM . |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | Carry out Programmable Module Installation (PMI). RETRIEVE RCM DTCs. If RCM DTC U0300:00 is retrieved on-demand during self-test, INSTALL a new RCM . Refer to RESTRAINTS CONTROL MODULE (RCM) in this information. |
| U0401:00 | Invalid Data Received From ECM/PCM: No Sub Type Information | Carry out self-test of the PCM and diagnose any DTCs present. Refer to INTRODUCTION or the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULE . |
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | CHECK for additional RCM and APIM DTCs. Refer to the appropriate information to diagnose the DTCs. If no other DTCs are present, refer to Accessory Protocol Interface Module (APIM) Software Level Check in the General Procedures portion of DRIVER INFORMATION SYSTEM & ENTERTAINMENT SYSTEM . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | Carry Out Programmable Module Installation (PMI). RETRIEVE RCM DTCs. If RCM DTC U0300:00 is retrieved on-demand during self-test, INSTALL a new RCM . Refer to RESTRAINTS CONTROL MODULE (RCM) in this information. |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | INSTALL a new RCM and carry out Programmable Module Installation (PMI). Use as built data when CARRYING out PMI for this DTC. Refer to RESTRAINTS CONTROL MODULE (RCM) in this information. |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | INSTALL a new RCM and carry out Programmable Module Installation (PMI). Refer to RESTRAINTS CONTROL MODULE (RCM) in this information. |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new RCM and carry out Programmable Module Installation (PMI). If DTC U2200:00 is also present, use as built data when CARRYING OUT PMI. Refer to RESTRAINTS CONTROL MODULE (RCM) in this information. |
| U3000:4A | Control Module: Incorrect Component Installed | Go to PINPOINT TEST K . |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | Carry Out Programmable Module Installation (PMI). Refer to MODULE COMMUNICATIONS NETWORK
. If DTC is retrieved a second time, INSTALL a new RCM . Refer to RESTRAINTS CONTROL MODULE (RCM) in this information. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | Go to PINPOINT TEST M . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | Go to PINPOINT TEST M . |