Parking Aid Module (PAM)
PARKING AID MODULE (PAM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B13B5:12 | Rear Center Sensor: Circuit Short To Battery | GO to PINPOINT TEST D |
| B13B5:14 | Rear Center Sensor: Circuit Short To Ground Or Open | GO to PINPOINT TEST C |
| B13B5:96 | Rear Center Sensor: Component Internal Failure | GO to PINPOINT TEST E |
| B1B44:12 | Right Rear Outer Sensor: Circuit Short To Battery | GO to PINPOINT TEST D |
| B1B44:14 | Right Rear Outer Sensor: Circuit Short To Ground Or Open | GO to PINPOINT TEST C |
| B1B44:96 | Right Rear Outer Sensor: Component Internal Failure | GO to PINPOINT TEST E |
| B1B48:12 | Left Rear Outer Sensor: Circuit Short To Battery | GO to PINPOINT TEST D |
| B1B48:14 | Left Rear Outer Sensor: Circuit Short To Ground Or Open | GO to PINPOINT TEST C |
| B1B48:96 | Left Rear Outer Sensor: Component Internal Failure | GO to PINPOINT TEST E |
| B1B58:11 | Rear Sensors Power Circuit: Circuit Short To Ground | GO to PINPOINT TEST B |
| U0001:88 | High Speed Can Communication Bus: Bus Off | The module could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC ). CLEAR the DTC . REPEAT the Network Test with the scan tool. VERIFY the integrity of the connectors and wiring Refer to SYSTEM WIRING DIAGRAMS for additional information. |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to PINPOINT TEST F |
| U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message | GO to PINPOINT TEST G |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to PINPOINT TEST H |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC
sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: PARKING ASSIST CONTROL MODULE (PAM) - VEHICLES WITH: 5-DOOR (413-13 Parking Aid, Removal and Installation). |
| U0401:86 | Invalid Data Received From ECM/PCM A: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the PCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0415:86 | Invalid Data Received From ABS Control Module: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the ABS module with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0420:86 | Invalid Data Received From Power Steering Control Module: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the PSCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0422:86 | Invalid Data Received From Body Control Module: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0428:86 | Invalid Data Received From Steering Angle Sensor Module: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the SASM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC
sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: PARKING ASSIST CONTROL MODULE (PAM) - VEHICLES WITH: 5-DOOR (413-13 Parking Aid, Removal and Installation). |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC
sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: PARKING ASSIST CONTROL MODULE (PAM) - VEHICLES WITH: 5-DOOR (413-13 Parking Aid, Removal and Installation). |
| U3000:47 | Control Module: Watchdog/Safety Microcontroller Failure | CLEAR the DTC . REPEAT the self-test. If DTC U3000:47 returns, INSTALL a new Parking Aid Module (PAM) REFER to: PARKING ASSIST CONTROL MODULE (PAM) - VEHICLES WITH: 5-DOOR (413-13 Parking Aid, Removal and Installation). |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the DTC . REPEAT the self-test. If DTC U3000:49 returns, INSTALL a new Parking Aid Module (PAM) REFER to: PARKING ASSIST CONTROL MODULE (PAM) - VEHICLES WITH: 5-DOOR (413-13 Parking Aid, Removal and Installation). |
| U3003:62 | Battery Voltage: Signal Compare Failure | GO to PINPOINT TEST I |