LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2013 >> Escape Titanium, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 233 (Anti-Lock Brake System (Abs) And Stability Control) >> Diagnosis And Testing >> Anti-Lock Brake System (ABS) and Stability Control >> Diagnostic Trouble Code (DTC) Charts >> DTC Chart: Steering Angle Sensor Module (SASM)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC Chart: Steering Angle Sensor Module (SASM)

WARNING: This page is about a different car, the 2014 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices.

Refer to: DIAGNOSTIC METHODS .

SASM DTC DESCRIPTION

DTC Description Action
C1B00:49 Steering Angle Sensor: Internal Electrical Failure
  • CHECK vehicle service history for recent service actions related to the SASM. This DTC  sets due to incomplete or improper flash programming procedures. If there have been recent service actions with the SASM  , REPEAT the programming procedure as directed by the diagnostic scan tool.
  • If there have been no recent service actions, CLEAR the DTC  , CYCLE the ignition, CARRY OUT the SASM  self-test. If the DTC  returns, INSTALL a new SASM  to correct the failure to retain software data.

    Refer to: STEERING ANGLE SENSOR MODULE (SASM) .
C1B00:61 Steering Angle Sensor: Signal Calculation Failure
  • This DTC  indicates that part of the SASM  has failed internally. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test.
  • If the DTC  returns, INSTALL a new SASM  .

    Refer to: STEERING ANGLE SENSOR MODULE (SASM) .
C1B00:62 Steering Angle Sensor: Signal Compare Failure This DTC  indicates that part of the SASM  has failed internally. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If the DTC  returns, INSTALL a new SASM  .
Refer to: STEERING ANGLE SENSOR MODULE (SASM) .
C1B00:64 Steering Angle Sensor: Signal Plausibility Failure CLEAR the DTC  . TEST DRIVE the vehicle and CARRY OUT at least 1 left turn and 1 right turn. CARRY OUT a SASM  self-test. If the DTC  returns, INSTALL a new SASM  .
Refer to: STEERING ANGLE SENSOR MODULE (SASM) .
C1B00:81 Steering Angle Sensor: Invalid Serial Data Received
  • This DTC  indicates that part of the SASM  has failed internally. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test.
  • If the DTC  returns, INSTALL a new SASM  .

    Refer to: STEERING ANGLE SENSOR MODULE (SASM) .
C1B00:85 Steering Angle Sensor: Signal Above Allowable Range
  • SET the front wheels to the straight ahead position.
  • Using a diagnostic scan tool, OBSERVE the SASM  steering wheel angle (SW_ANGLE) PID  .
  • If the PID  displays 0 degrees, CLEAR the DTC  , REPEAT the SASM  self-test. If the DTC  returns, INSTALL a new SASM  .

    Refer to: STEERING ANGLE SENSOR MODULE (SASM) .

  • If the PID  displays more than 360 degrees, SET the ignition to OFF. REMOVE the SASM  ,

    Refer to: STEERING ANGLE SENSOR MODULE (SASM) . Leave the electrical connector connected  . SET the ignition to ON (this causes Diagnostic Trouble Codes (DTCs) to set in multiple modules). Manually ADJUST the SASM  until the SW_ANGLE PID  displays 0 degrees. SET the ignition to OFF. INSTALL the SASM  . CLEAR all Continuous Memory Diagnostic Trouble Codes (CMDTCs) in all modules.
C1B00:87 Steering Angle Sensor: Missing Message
  • The module could not communicate on the network at a point in time. The fault is not currently present since the module is able to communicate with the diagnostic scan tool to report this DTC  .
  • VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information.
C1B00:92 Steering Angle Sensor: Performance or Incorrect Operation CLEAR the DTC  . TEST DRIVE the vehicle and CARRY OUT at least 1 left turn and 1 right turn. CARRY OUT a SASM  self-test. If the DTC  returns, INSTALL a new SASM  .
Refer to: STEERING ANGLE SENSOR MODULE (SASM) .
C1B00:96 Steering Angle Sensor: Component Internal Failure
  • This DTC  indicates that part of the SASM  has failed internally. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test.
  • If the DTC  returns, INSTALL a new SASM  .

    Refer to: STEERING ANGLE SENSOR MODULE (SASM) .
U0001:88 High Speed CAN Communication Bus: Bus Off
  • The module could not communicate on the network at a point in time. The fault is not currently present since the module is able to communicate with the diagnostic scan tool to report this DTC  .
  • VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information.
U0140:00 Lost Communication With Body Control Module: No Sub Type Information GO to PINPOINT TEST D 
U0300:00 Internal Control Module Software Incompatibility: No Sub Type Information GO to PINPOINT TEST P 
U3003:62 Battery Voltage: Signal Compare Failure GO to PINPOINT TEST K 
scientia non olet · About LEMON Manuals