LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2013 >> Focus S, Standard Trans, Gas/Ethanol >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 12 (Automatic Dual Clutch Transaxle (DCT) POWERSHIFT (DPS6/6DCT250) - External Controls) >> Diagnosis and Testing >> External Controls >> Pinpoint Tests >> Possible Sources >> Pinpoint Test C: SELECTSHIFT™
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Pinpoint Test C: SELECTSHIFT™

WARNING: This page is about a different variant/trim than selected.
  1. C1 RETRIEVE AND RECORD ALL DTCS
    • Using the diagnostic scan tool, retrieve all Diagnostic Trouble Codes (DTCs).

    IS DTC P0815 or P0816 present? 

    1. Yes:  If DTC P0815 is present, GO to C2 
    2. No:  If DTC P0816 is present, GO to  C7
  2. C2 CHECK THE UPSHIFT SIGNAL CIRCUIT FOR VOLTAGE 
    • Disconnect Floor Shifter C3245  .
    • Inspect for damaged or pushed-out terminals.
    • Ignition ON.
    • Measure the voltage  between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C3245-9 
      G08064039
      		 -

    Is the voltage greater than 11 volts? 

    1. Yes:  GO to  C5
    2. No:  GO to C3 
  3. C3 CHECK THE UPSHIFT SIGNAL CIRCUIT FOR AN OPEN 
    • Ignition OFF.
    • Disconnect TCM C1750A  .
    • Inspect for damaged or pushed-out terminals.
    • Measure the resistance  between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C1750A-9  Ω C3245-9 

    Is the resistance less than 3 ohms? 

    1. Yes:  GO to C4 
    2. No:  REPAIR the circuit.
  4. C4 CHECK THE UPSHIFT SIGNAL CIRCUIT FOR A SHORT TO GROUND 
    • Measure the resistance  between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C3245-9  Ω -

    Is the resistance greater than 10, 000 ohms? 

    1. Yes:  GO to  C6
    2. No:  REPAIR the circuit.
  5. C5 CHECK THE SIGNAL RETURN CIRCUIT FOR AN OPEN 
    • Measure the voltage  between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C3245-9 
      G08064039
      		 C3245-8 

    Is the voltage greater than 11 volts? 

    1. Yes:  GO to C6 
    2. No:  REPAIR the circuit. If an open circuit is not found, INSTALL a new TCM.

      REFER to: Transmission Control Module (TCM)  ( TRANSMISSION CONTROL MODULE (TCM) .

  6. C6 CHECK THE SELECTSHIFT™ SWITCH 
    • Disconnect SelectShift™ connector in the selector lever assembly.
    • Measure the component side resistance  while cycling the SelectShift™ upshift switch between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C3245-9  Ω C3245-8 

    Is the resistance less than 1.5 ohms with upshift selected and greater than 10, 000 ohms when released? 

    1. Yes:  CHECK OASIS  for any applicable TSB. If a TSB exists for this concern, discontinue this test and follow the TSB instructions. If no TSB address this concern, INSTALL a new TCM.

      REFER to: Transmission Control Module (TCM)  ( TRANSMISSION CONTROL MODULE (TCM) .

    2. No:  INSTALL a new selector lever knob.

      REFER to: Selector Lever Knob  .

  7. C7 CHECK THE DOWNSHIFT SIGNAL CIRCUIT FOR VOLTAGE 
    • Disconnect Floor Shifter C3245  .
    • Inspect for damaged or pushed-out terminals.
    • Ignition ON.
    • Measure the voltage  between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C3245-10 
      G08064039
      		 -

    Is the voltage greater than 11 volts? 

    1. Yes:  GO to  C10
    2. No:  GO to C8 
  8. C8 CHECK THE DOWNSHIFT SIGNAL CIRCUIT FOR AN OPEN 
    • Ignition OFF.
    • Disconnect TCM C1750A  .
    • Inspect for damaged or pushed-out terminals.
    • Measure the resistance  between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C1750A-10  Ω C3245-10 

    Is the resistance less than 3 ohms? 

    1. Yes:  GO to C9 
    2. No:  REPAIR the circuit.
  9. C9 CHECK THE DOWNSHIFT SIGNAL CIRCUIT FOR A SHORT TO GROUND 
    • Measure the resistance  between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C3245-10  Ω -

    Is the resistance greater than 10, 000 ohms? 

    1. Yes:  GO to C10 
    2. No:  REPAIR the circuit.
  10. C10 CHECK THE SIGNAL RETURN CIRCUIT FOR AN OPEN 
    • Measure the voltage  between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C3245-3 
      G08064039
      		 -

    Is the voltage greater than 11 volts? 

    1. Yes:  GO to C11 
    2. No:  REPAIR the circuit. If an open circuit is not found, INSTALL a new TCM.

      REFER to: Transmission Control Module (TCM)  ( TRANSMISSION CONTROL MODULE (TCM) .

  11. C11 CHECK THE SELECTSHIFT™ SWITCH 
    • Disconnect SelectShift™ connector in the selector lever assembly.
    • Measure the component side resistance  while cycling the SelectShift™ upshift switch between.

      Click to display connectors 

      Positive Lead Measurement / Action Negative Lead
      C3245-10  Ω C3245-8 

    Is the resistance less than 1.5 ohms with upshift selected and greater than 10, 000 ohms when released? 

    1. Yes:  CHECK OASIS  for any applicable TSB. If a TSB exists for this concern, discontinue this test and follow the TSB instructions. If no TSB address this concern, INSTALL a new TCM.

      REFER to: Transmission Control Module (TCM)  ( TRANSMISSION CONTROL MODULE (TCM) .

    2. No:  INSTALL a new selector lever knob.

      REFER to: Selector Lever Knob  .

scientia non olet · About LEMON Manuals