IPMA DTC Table
IPMA DTC CHART
| DTC | Description | Action |
|---|---|---|
| B11C7:46 | High Beam Sensor: Calibration/Parameter Memory Failure | REFER to: HEADLAMPS . |
| B11C7:97 | High Beam Sensor: Component or System Operation Obstructed or Blocked | REFER to: HEADLAMPS . |
| B1286:14 | Interior Mirror: Circuit Short To Ground or Open | GO to PINPOINT TEST F |
| B12D8:11 | Mirror Heater Output: Circuit Short To Ground | GO to PINPOINT TEST H |
| B12D8:13 | Mirror Heater Output: Circuit Open | GO to PINPOINT TEST H |
| C1001:78 | Vision System Camera: Alignment or Adjustment Incorrect | This DTC sets when a new IPMA has been installed without performing the camera alignment. PERFORM the camera alignment using a diagnostic scan tool. |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to PINPOINT TEST I |
| U0104:87 | Lost Communication With Cruise Control Module: Missing Message | GO to PINPOINT TEST J |
| U0131:87 | Lost Communication With Power Steering Control Module: Missing Message | GO to PINPOINT TEST K |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to PINPOINT TEST L |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to PINPOINT TEST M |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC): Missing Message | GO to PINPOINT TEST N |
| U0212:87 | Lost Communication With Steering Column Control Module: Missing Message | GO to PINPOINT TEST O |
| U0232:87 | Lost Communication With Side Obstacle Detection Control Module - Left: Missing Message | GO to PINPOINT TEST P |
| U0233:87 | Lost Communication With Side Obstacle Detection Control Module - Right: Missing Message | GO to PINPOINT TEST Q |
| U0401:00 | Invalid Data Received From ECM/PCM A: No Sub Type Information | This DTC can set due to a fault in the PCM or an input to the PCM . CARRY OUT a self-test of the PCM and DIAGNOSE any Diagnostic Trouble Codes (DTCs) present. REFER to Refer to the appropriate Engine Mechanical article for the procedure. REFER to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) (SECTION 0) . |
| U0405:00 | Invalid Data Received From Cruise Control Module: No Sub Type Information | This DTC can set due to a fault in the CCM or an input to the CCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in all modules on the network. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC can set due to a fault in the BCM or an input to the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in all modules on the network. |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | This DTC can set due to a fault in the IPC or an input to the IPC. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in all modules on the network. |
| U0429:00 | Invalid Data Received From Steering Column Control Module: No Sub Type Information | This DTC can set due to a fault in the SCCM or an input to the SCCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in all modules on the network. |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | This DTC can set due to a fault in the RCM or an input to the RCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in all modules on the network. |
| U1000:11 | Solid State Driver Protection Activated: Circuit Short To Ground | The IPMA
has temporarily disabled the camera windshield heater defroster output because an excessive current draw exists (such as a short to ground). The IPMA
cannot enable the output until the cause of the short is corrected. ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMA self-test to enable the output driver. |
| U201A:54 | Control Module Main Calibration Data: Missing Calibration | CHECK the vehicle service history for recent service actions related to this module. This DTC
sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: INTERIOR REAR VIEW MIRROR . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC
sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: INTERIOR REAR VIEW MIRROR . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC
sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: INTERIOR REAR VIEW MIRROR . |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC
sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: INTERIOR REAR VIEW MIRROR . |
| U3000:42 | Control Module: General Memory Failure | ADDRESS all other IPMA
DTCs. If this DTC
is still present AFTER all other Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. REFER to: INTERIOR REAR VIEW MIRROR . |
| U3000:49 | Control Module: Internal Electronic Failure | The IPMA
has permanently disabled an output because an excessive current draw has occurred more times than the module can withstand. ADDRESS all other IPMA
Diagnostic Trouble Codes (DTCs). If this DTC
is still present AFTER all other IPMA
Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. REFER to: INTERIOR REAR VIEW MIRROR . |
| U3000:93 | Control Module: No Operation | ADDRESS all other IPMA
Diagnostic Trouble Codes (DTCs). If this DTC is still present AFTER all other IPMA
Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. REFER to: INTERIOR REAR VIEW MIRROR . |
| U3000:96 | Control Module: Component Internal Failure | ADDRESS all other IPMA
Diagnostic Trouble Codes (DTCs). AFTER all other IPMA
Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. REFER to: INTERIOR REAR VIEW MIRROR . |