Audio Control Module (ACM) - Premium DTC Table
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1A01:01 | Speaker #1: General Electrical Failure |
|
| B1A01:11 | Speaker #1: Circuit Short To Ground |
|
| B1A01:12 | Speaker #1: Circuit Short To Battery |
|
| B1A01:13 | Speaker #1: Circuit Open |
|
| B1A02:01 | Speaker #2: General Electrical Failure |
|
| B1A02:11 | Speaker #2: Circuit Short To Ground |
|
| B1A02:12 | Speaker #2: Circuit Short To Battery |
|
| B1A02:13 | Speaker #2: Circuit Open |
|
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST K |
| B1A03:11 | Speaker #3: Circuit Short To Ground | GO to PINPOINT TEST K |
| B1A03:12 | Speaker #3: Circuit Short To Battery | GO to PINPOINT TEST K |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST K |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to PINPOINT TEST L |
| B1A04:11 | Speaker #4: Circuit Short To Ground | GO to PINPOINT TEST L |
| B1A04:12 | Speaker #4: Circuit Short To Battery | GO to PINPOINT TEST L |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST L |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | If DTC B1A56:21 sets after running the bezel diagnostic tests, disregard this DTC . This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency, the test will fail. Therefore, tests ran from the bezel diagnostic screen and the DTC generated from the test can be disregarded. |
| B1A89:11 | Satellite Antenna: Circuit Short To Ground | GO to PINPOINT TEST B |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST B |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTC . This is normal operation. |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure |
|
| U0155:00 | Lost Communication With IPC Control Module: No Sub Type Information | GO to PINPOINT TEST AB |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to PINPOINT TEST AD |
| U0257:00 | Lost Communication With Front Control/Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AE |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to: AUDIO FRONT CONTROL MODULE (ACM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to: AUDIO FRONT CONTROL MODULE (ACM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION (418-01 Module Configuration, Description and Operation). See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to: AUDIO FRONT CONTROL MODULE (ACM) . |
| U3000:41 | Control Module: General Checksum Failure |
|
| U3000:42 | Control Module: General Memory Failure |
|
| U3000:96 | Control Module: Component Internal Failure | GO to PINPOINT TEST B |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AF |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AG |