DTC Chart: Audio DSP Module
WARNING: This page is about a different variant/trim than selected.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: DIAGNOSTIC METHODS .
| DTC | Description | Action |
|---|---|---|
| B1045:13 | Chime: Circuit Open | REFER to: INSTRUMENTATION, MESSAGE CENTER AND WARNING CHIMES . |
| B13FB:11 | Audio Enable Line: Circuit Short To Ground | GO to PINPOINT TEST AI |
| B13FD:13 | Chime Input 2: Circuit Open | REFER to: INSTRUMENTATION, MESSAGE CENTER AND WARNING CHIMES . |
| B1A01:01 | Speaker #1: General Electrical Failure | GO to PINPOINT TEST J |
| B1A01:11 | Speaker #1: Circuit Short To Ground | GO to PINPOINT TEST J |
| B1A01:12 | Speaker #1: Circuit Short To Battery | GO to PINPOINT TEST J |
| B1A01:13 | Speaker #1: Circuit Open | GO to PINPOINT TEST J |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to PINPOINT TEST H |
| B1A02:11 | Speaker #2: Circuit Short To Ground | GO to PINPOINT TEST H |
| B1A02:12 | Speaker #2: Circuit Short To Battery | GO to PINPOINT TEST H |
| B1A02:13 | Speaker #2: Circuit Open | GO to PINPOINT TEST H |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST I |
| B1A03:11 | Speaker #3: Circuit Short To Ground | GO to PINPOINT TEST I |
| B1A03:12 | Speaker #3: Circuit Short To Battery | GO to PINPOINT TEST I |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST I |
| B1A04:01 | Speaker #4: General Electrical Failure | For LHR door speaker, GO to PINPOINT TEST R For LHR tweeter speaker, GO to PINPOINT TEST S |
| B1A04:11 | Speaker #4: Circuit Short To Ground | For LHR door speaker, GO to PINPOINT TEST R For LHR tweeter speaker, GO to PINPOINT TEST S |
| B1A04:12 | Speaker #4: Circuit Short To Battery | For LHR door speaker, GO to PINPOINT TEST R For LHR tweeter speaker, GO to PINPOINT TEST S |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST R |
| B1A05:01 | Speaker #5: General Electrical Failure | GO to PINPOINT TEST P |
| B1A05:11 | Speaker #5: Circuit Short To Ground | GO to PINPOINT TEST P |
| B1A05:12 | Speaker #5: Circuit Short To Battery | GO to PINPOINT TEST P |
| B1A05:13 | Speaker #5: Circuit Open | GO to PINPOINT TEST P |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to PINPOINT TEST K |
| B1A06:11 | Speaker #6: Circuit Short To Ground | GO to PINPOINT TEST K |
| B1A06:12 | Speaker #6: Circuit Short To Battery | GO to PINPOINT TEST K |
| B1A06:13 | Speaker #6: Circuit Open | GO to PINPOINT TEST K |
| B1A07:01 | Speaker #7: General Electrical Failure | GO to PINPOINT TEST L |
| B1A07:11 | Speaker #7: Circuit Short To Ground | GO to PINPOINT TEST L |
| B1A07:12 | Speaker #7: Circuit Short To Battery | GO to PINPOINT TEST L |
| B1A07:13 | Speaker #7: Circuit Open | GO to PINPOINT TEST L |
| B1A08:01 | Speaker #8: General Electrical Failure | For RHR door speaker, GO to PINPOINT TEST M For RHR tweeter speaker, GO to PINPOINT TEST N |
| B1A08:11 | Speaker #8: Circuit Short To Ground | For RHR door speaker, GO to PINPOINT TEST M For RHR tweeter speaker, GO to PINPOINT TEST N |
| B1A08:12 | Speaker #8: Circuit Short To Battery | For RHR door speaker, GO to PINPOINT TEST M For RHR tweeter speaker, GO to PINPOINT TEST N |
| B1A08:13 | Speaker #8: Circuit Open | GO to PINPOINT TEST M |
| B1A09:11 | Speaker #9: Circuit Short To Ground | GO to PINPOINT TEST O |
| B1A09:12 | Speaker #9: Circuit Short To Battery | GO to PINPOINT TEST O |
| B1A09:13 | Speaker #9: Circuit Open | GO to PINPOINT TEST O |
| B1A10:11 | Speaker #10: Circuit Short To Ground | GO to PINPOINT TEST Q |
| B1A10:12 | Speaker #10: Circuit Short To Battery | GO to PINPOINT TEST Q |
| B1A10:13 | Speaker #10: Circuit Open | GO to PINPOINT TEST Q |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AM |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AO |
| U0237:00 | Lost Communication With Digital Audio Control Module "C": No Sub Type Information | GO to PINPOINT TEST AP |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to PINPOINT TEST AR |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST AS |
| U0257:00 | Lost Communication With Front Controls/Display Interface Module: No Sub Type Information |
NOTE:
Despite the description, this DTC applies to the FDIM, not the FCDIM. GO to PINPOINT TEST AT |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and follow Diagnostic Trouble Codes (DTCs) present in the REFER to: INSTRUMENTATION, MESSAGE CENTER AND WARNING CHIMES . |
| U2014:01 | Control Module Hardware: General Electrical Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U2014:01 is still present, INSTALL a new audio DSP module. REFER to: AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U2014:41 is still present, INSTALL a new audio DSP module. REFER to: AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . REPEAT the self-test. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new audio DSP module. REFER to: AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . REPEAT the self-test. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AW |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AX |