Cruise Control Module (CCM) DTC Table
CCM DTC CHART
| DTC | Description | Action |
|---|---|---|
| B142E:78 | Forward Looking Sensor Horizontal Alignment: Alignment or Adjustment Incorrect | GO to PINPOINT TEST H |
| B1432:78 | Forward Looking Sensor Vertical Alignment: Alignment of Adjustment Incorrect | This DTC can only be set at the assembly plant during the plant alignment process. If DTC B1432:78 sets, a reflash of the CCM and the vertical and horizontal aim procedure must be performed. REFER to: CRUISE CONTROL RADAR ALIGNMENT . |
| B1433:54 | Forward Looking Sensor Alignment: Missing Calibration | GO to PINPOINT TEST H |
| C0072:00 | Brake Temperature Too High: No Sub Type Information | Refer to: ANTI-LOCK BRAKE SYSTEM (ABS) AND STABILITY CONTROL - VEHICLES BUILT UP TO: 03-06-2013 . |
| C1132:4B | Head Up Display: Over Temperature | REFER to: COLLISION WARNING SYSTEM . |
| C1A67:96 | Forward Looking Sensor: Component Internal Failure | GO to PINPOINT TEST I |
| C1A67:97 | Forward Looking Sensor: Component or System Operation Obstructed or Blocked | GO to PINPOINT TEST J |
| C1A67:98 | Forward Looking Sensor: Component or System Over Temperature | The CCM was over-temperature. This may occur during extended use of extremely high weather temperatures. The adaptive cruise control system operation resumes after the CCM cools. |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | REFER to: COMMUNICATIONS NETWORK . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to PINPOINT TEST K |
| U0101:00 | Lost Communication with TCM: No Sub Type Information | GO to PINPOINT TEST K |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to PINPOINT TEST F |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST L |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST M |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST N |
| U0158:00 | Lost Communication With Head Up Display: No Sub Type Information | GO to PINPOINT TEST O |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to PINPOINT TEST P |
| U0401:86 | Invalid Data Received From ECM/PCM "A": Signal Invalid | This DTC sets when the CCM receives invalid network data from the PCM with a faulted vehicle speed sensor signal, accelerator pedal position signal or cruise control switch input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0402:86 | Invalid Data Received From TCM: Signal Invalid | This DTC sets when the CCM receives invalid network data from the PCM with a faulted gear lever position input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in other modules on the network. |
| U0418:86 | Invalid Data Received From Brake System Control Module: Signal Invalid | This DTC sets when the CCM receives invalid network data from the ABS module with a faulted brake signal input, yaw rate input, steering wheel angle input or vehicle speed input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0423:82 | Invalid Data Received From Instrument Panel Cluster Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to PINPOINT TEST U |
| U0429:86 | Invalid Data Received From Steering Column Control Module: Signal Invalid | This DTC sets when the CCM receives invalid network data from the SCCM with a faulted cruise control switch input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | This DTC sets when the CCM receives invalid network data from the RCM with a faulted yaw rate input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: CRUISE CONTROL MODULE (CCM) . |
| U0459:86 | Invalid Data Received From Head Up Display: Signal Invalid | GO to PINPOINT TEST Q |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets when the CCM configuration has not been completed. CARRY OUT the PMI (when the original module is not available) for the module in question as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . |
| U2300:55 | Central Configuration: Not Configured | This DTC sets when the CCM detects that the BCM is not configured correctly. CARRY OUT the PMI (when the original module is not available) for the module in question as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . |
| U2300:64 | Central Configuration: Signal Plausibility Failure | This DTC sets when the CCM detects that the BCM is not configured correctly. CARRY OUT the PMI (when the original module is not available) for the module in question as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self test. If DTC U3000:41 is retrieved again, INSTALL a new CCM. REFER to: CRUISE CONTROL MODULE (CCM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new CCM. REFER to: CRUISE CONTROL MODULE (CCM) . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self-test. If DTC U3000:44 is retrieved again, INSTALL a new CCM. REFER to: CRUISE CONTROL MODULE (CCM) . |
| U3000:49 | Control Module: Internal Electronic Failure | If DTC U3000:49 is retrieved again, INSTALL a new CCM. REFER to: CRUISE CONTROL MODULE (CCM) . |
| U3000:63 | Control Module: Circuit/Component Protection Time-Out | GO to PINPOINT TEST R |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | This DTC sets when the stored VIN in the CCM does not match the VIN defined in the BCM. This may indicate that the original CCM is not installed in the vehicle, and has not been configured correctly. CARRY OUT the PMI (when the original module is not available) for the module in question as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST S |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST T |