DTC Chart: APIM
WARNING: This page is about a different variant/trim than selected.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: DIAGNOSTIC METHODS .
| DTC | Description | Action |
|---|---|---|
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to: PARKING AID . |
| B108E:01 | Display: General Electrical Failure | GO to PINPOINT TEST W |
| B116A:01 | Handset Microphone: General Electrical Failure | GO to PINPOINT TEST R |
| B1215:00 | External Memory Card: No Sub Type Information | GO to PINPOINT TEST S |
| B1252:11 | USB Port: Circuit Short To Ground | GO to PINPOINT TEST S |
| B1252:13 | USB Port: Circuit Open | GO to PINPOINT TEST S |
| B12B8:11 | USB Port #2: Circuit Short To Ground |
NOTE:
This DTC refers to USB port #2 on the APIM itself, which is not used. INSPECT the APIM USB port #2 for damage and remove any debris. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC B12B8:11 is retrieved again, refer to APIM HARDWARE TESTING |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST AF |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AG |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to PINPOINT TEST W |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to PINPOINT TEST AH |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AI |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST AL |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and follow Diagnostic Trouble Codes (DTCs) present in the IPC. REFER to: INSTRUMENTATION, MESSAGE CENTER AND WARNING CHIMES . |
| U1A00:87 | Private Communication Network: Missing Message | GO to PINPOINT TEST C |
| U2017:45 | Control Module Software #2: Program Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U2017:45 is still present, refer to APIM HARDWARE TESTING |
| U2017:51 | Control Module Software #2: Not Programmed | PROGRAM the APIM. REFER to: MODULE CONFIGURATION . CLEAR the DTC. REPEAT the self-test. If DTC U2017:54 is still present, refer to APIM HARDWARE TESTING |
| U2017:52 | Control Module Software #2: Not Activated | PROGRAM the APIM. REFER to: MODULE CONFIGURATION . CLEAR the DTC. REPEAT the self-test. If DTC U2017:54 is still present, refer to APIM HARDWARE TESTING |
| U2017:54 | Control Module Software #2: Missing Calibration | PROGRAM the APIM. REFER to: MODULE CONFIGURATION . CLEAR the DTC. REPEAT the self-test. If DTC U2017:54 is still present, refer to APIM HARDWARE TESTING |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the APIM PROGRAMMING as directed by the scan tool. REFER to: INFORMATION AND ENTERTAINMENT SYSTEM - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See APIM PROGRAMMING . If there have been no recent service actions, refer to APIM HARDWARE TESTING |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the APIM PROGRAMMING as directed by the scan tool. REFER to: INFORMATION AND ENTERTAINMENT SYSTEM - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See APIM PROGRAMMING . If there have been no recent service actions, refer to APIM HARDWARE TESTING |
| U3000:04 | Control Module: System Internal Failure |
|
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:41 is still present, refer to APIM HARDWARE TESTING |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:42 is still present, refer to APIM HARDWARE TESTING |
| U3000:88 | Control Module: Bus off |
NOTE:
Network communication/message Diagnostic Trouble Codes (DTCs) may result from intermittent concerns such as damaged wiring or low battery voltage occurrences. Additionally, vehicle repair procedures such as module reprogramming often set these Diagnostic Trouble Codes (DTCs). To avoid repeat network concerns, inspect for damaged or corroded wiring at the APIM. Test the vehicle battery, refer to CHARGING SYSTEM - GENERAL INFORMATION
. Replacing a module to resolve a network DTC is unlikely to resolve the concern. The module could not communicate on the network at a point in time. The fault is currently not present. CLEAR the DTC. REPEAT the network test with the scan tool. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AP |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AQ |