DTC Chart: Heating Ventilation Air Conditioning (HVAC) Module - Dual Automatic Temperature Control (DATC)
WARNING: This page is about a different car, the 2015 Ford C-Max. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Network Diagnostic Trouble Codes (DTCs) (U-codes) are often a result of intermittent concerns such as damaged wiring or low battery voltage occurrences. Additionally, vehicle repair procedures, such as module reprogramming, often set network Diagnostic Trouble Codes (DTCs). Replacing a module to resolve a network DTC is unlikely to resolve the concern. To prevent repeat network DTC concerns, inspect all network wiring, especially connectors. Test the vehicle battery. REFER to: Battery .
HVAC Control Module - DATC DTC Chart
| DTC | Description | Action |
|---|---|---|
| B105A:00 | Cabin Temperature Sensor Fan: No Sub Type Information | GO to Pinpoint Test P |
| B1081:00 | Left Temperature Damper Motor: No Sub Type Information | GO to Pinpoint Test K |
| B1082:00 | Right Temperature Damper Motor: No Sub Type Information | GO to Pinpoint Test L |
| B1083:00 | Recirculation Damper Motor: No Sub Type Information | GO to Pinpoint Test F |
| B1085:00 | Defroster Damper Motor: No Sub Type Information | GO to Pinpoint Test G |
| B1086:00 | Air Distribution Damper Motor: No Sub Type Information | GO to Pinpoint Test G |
| B10B3:00 | Right Panel Air Discharge Temperature: No Sub Type Information | GO to Pinpoint Test O |
| B10B4:00 | Right Floor Air Discharge Temperature: No Sub Type Information | GO to Pinpoint Test O |
| B10B5:00 | Left Panel Air Discharge Temperature: No Sub Type Information | GO to Pinpoint Test O |
| B10B6:00 | Left Floor Air Discharge Temperature: No Sub Type Information | GO to Pinpoint Test O |
| B10B8:00 | Push Buttons: No Sub Type Information | INSTALL a new HVAC control module. REFER to: Heating, Ventilation and Air Conditioning (HVAC) Control Module . |
| B10B9:00 | Blower Control: No Sub Type Information | GO to Pinpoint Test N |
| B1A61:00 | Cabin Temperature Sensor: No Sub Type Information | GO to Pinpoint Test P |
| B1A63:00 | Right Solar Sensor: No Sub Type Information | GO to Pinpoint Test Q |
| B1A64:00 | Left Solar Sensor: No Sub Type Information | GO to Pinpoint Test Q |
| B1A69:00 | Humidity Sensor: No Sub Type Information | GO to Pinpoint Test P |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test C |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test S |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM. REFER to: Body Control Module (BCM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new HVAC control module to correct the failure to retain configuration data. REFER to: Heating, Ventilation and Air Conditioning (HVAC) Control Module . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new HVAC control module to correct the failure to retain configuration data. REFER to: Heating, Ventilation and Air Conditioning (HVAC) Control Module . |
| U3000:00 | Control Module: No Sub Type Information | INSTALL a new HVAC control module. REFER to: Heating, Ventilation and Air Conditioning (HVAC) Control Module . |
| U3006:16 | Control Module Input Power "A": Circuit Voltage Below Threshold | GO to Pinpoint Test R |
| U3006:17 | Control Module Input Power "A": Circuit Voltage Above Threshold | GO to Pinpoint Test R |