Pinpoint Test F : DTC (Diagnostic Trouble Code) U0151:00
WARNING: This page is about a different car, the 2015 Ford C-Max. However, it is still accessible from the selected car via links, so may be relevant.
- F1 VERIFY THE CUSTOMER CONCERN
- Ignition ON.
- Verify there is an observable symptom present.
Is an observable symptom present?
Yes GO to F2 No The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition. CLEAR the DTC. - F2 CHECK THE COMMUNICATION NETWORK
- Using a diagnostic scan tool, perform a network test.
Does the RCM pass the network test?
Yes GO to F3 No DIAGNOSE no communication with the RCM. REFER to: Communications Network . - F3 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE BCM (BODY CONTROL MODULE) SELF-TEST
- Using a diagnostic scan tool, perform the BCM self-test.
Is DTC U3003:16 or DTC U3003:17 recorded?
Yes For DTC U3003:16, GO to Pinpoint Test N For DTC U3003:17, GO to Pinpoint Test O No GO to F4 - F4 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE RCM (RESTRAINTS CONTROL MODULE) SELF-TEST
- Using a diagnostic scan tool, perform the RCM self-test.
Is DTC U3003:16 or DTC U3003:17 recorded?
Yes REFER to: Airbag Supplemental Restraint System (SRS) . No GO to F5 - F5 RECHECK THE BCM (BODY CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)NOTE: If new modules were installed prior to the DTC being set, the module configuration may be incorrectly set during the PMI or the PMI may not have been carried out.
- Clear the Diagnostic Trouble Codes (DTCs).
- Ignition OFF.
- Wait 10 seconds.
- Ignition ON.
- Using a diagnostic scan tool, perform the BCM self-test.
Is DTC U0151:00 still present?
Yes GO to F6 No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition. CLEAR the DTC. - F6 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0151:00 SET IN OTHER MODULES
- Clear all Diagnostic Trouble Codes (DTCs).
- Ignition OFF.
- Ignition ON.
- Wait 10 seconds.
- Using a diagnostic scan tool, retrieve all Continuous Memory Diagnostic Trouble Codes (CMDTCs).
Is DTC U0151:00 set in any other module?
Yes GO to F7 No GO to F8 - F7 CHECK FOR CORRECT RCM (RESTRAINTS CONTROL MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect all RCM connectors.
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect the RCM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues. - F8 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect all BCM connectors.
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect the BCM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new BCM. REFER to: Body Control Module (BCM) . No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.