LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2015 >> Focus ST >> Repair and Diagnosis >> General Information >> DTC Index (Except Electric) >> Lane Keeping System DTCS >> IPMA
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Lane Keeping System DTCS: IPMA

DTC INDEX

DTC Description Action
B115E:54 Camera Module: Missing Calibration This DTC sets when a new IPMA has been installed without performing the camera alignment. PERFORM the camera alignment using a diagnostic scan tool.
B1304:82 Electronic Power Assisted Steering System: Alive/Sequence Counter Incorrect/Not Updated This DTC sets when the IPMA receives invalid network data from the PSCM. RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) in the PSCM. If no Diagnostic Trouble Codes (DTCs) are present in the PSCM, DIAGNOSE the observable symptom.
B1385:67 Lane Keeping Aid System: Signal Incorrect After Event GO to Pinpoint Test D
C1001:78 Vision System Camera: Alignment or Adjustment Incorrect This DTC sets when the IPMA camera alignment is out of specification.
VERIFY the IPMA is correctly attached to the mounting bracket.
PERFORM the camera alignment using a diagnostic scan tool.
U0001:88 High Speed CAN Communication Bus: Bus off A HS-CAN fault was present at a point in time. The fault is not currently present since the IPMA is communicating with the diagnostic scan tool. CLEAR the DTC and REPEAT the network test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to Wiring Diagrams MODULE COMMUNICATIONS NETWORK for schematic and connector information.
U0100:82 Lost Communication With ECM/PCM "A": Alive/Sequence Counter Incorrect / Not Updated GO to Pinpoint Test F
U0121:00 Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information GO to Pinpoint Test G
U0121:82 Lost Communication With Anti-Lock Brake System (ABS) Control Module Alive/Sequence Counter Incorrect/Not Updated GO to Pinpoint Test G
U0126:00 Lost Communication With Steering Angle Sensor Module: No Sub Type Information GO to Pinpoint Test H
U0131:87 Lost Communication With Power Steering Control Module: Missing Message GO to Pinpoint Test I
U0140:00 Lost Communication With Body Control Module: No Sub Type Information GO to Pinpoint Test J
U0140:82 Lost Communication With Body Control Module: Alive/Sequence Counter Incorrect/Not Updated GO to Pinpoint Test J
U0151:00 Lost Communication With Restraints Control Module: No Sub Type Information GO to Pinpoint Test K
U0401:81 Invalid Data Received From ECM/PCM A: Invalid Serial Data Received This DTC sets when the IPMA receives invalid network data from the PCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom.
U0402:81 Invalid Data Received from TCM: Invalid Serial Data Received This DTC sets when the IPMA receives invalid network data from the TCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the TCM. If no Diagnostic Trouble Codes (DTCs) are present in the TCM, DIAGNOSE the observable symptom.
U0415:00 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the ABS module with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module. If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom.
U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM. If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom.
U0422:81 Invalid Data Received From Body Control Module: Invalid Serial Data Received This DTC sets when the IPMA receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM. If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom.
U0423:00 Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the IPC with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the IPC. If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom.
U0423:81 Invalid Data Received from Instrument Panel Cluster Control Module: Invalid Serial Data Received This DTC sets when the IPMA receives invalid network data from the IPC with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the IPC. If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom.
U0428:00 Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the SASM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SASM. If no Diagnostic Trouble Codes (DTCs) are present in the SASM, DIAGNOSE the observable symptom.
U0428:83 Invalid Data Received From Steering Angle Sensor Module Value of Signal Protection Calculation Incorrect This DTC sets when the IPMA receives invalid network data from the SASM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SASM. If no Diagnostic Trouble Codes (DTCs) are present in the SASM, DIAGNOSE the observable symptom.
U0452:00 Invalid Data Received From Restraints Control Module: No Sub Type Information This DTC sets when the IPMA receives invalid network data from the RCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM. If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom.
U1000:11 Solid State Driver Protection Active - Driver Disabled: Circuit Short To Ground The IPMA has temporarily disabled the camera windshield heater defroster output because an excessive current draw exists (such as a short to ground). The IPMA cannot enable the output driver until the short is corrected. ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMA self-test to enable the output driver.
U1000:49 Solid State Driver Protection Active - Driver Disabled Internal Electronic Failure CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMA self test. If the DTC returns, INSTALL a new IPMA. REFER to: Image Processing Module A (IPMA)
U2100:00 Initial Configuration Not Complete: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description If there have been no recent service actions, INSTALL a new IPMA to correct the failure to retain configuration data. REFER to: Image Processing Module A (IPMA)
U2101:00 Control Module Configuration Incompatible: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description If there have been no recent service actions, INSTALL a new IPMA to correct the failure to retain configuration data. REFER to: Image Processing Module A (IPMA)
U3000:00 Control Module: No Sub Type Information CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMA self test. If the DTC returns, INSTALL a new IPMA. REFER to: Image Processing Module A (IPMA)
scientia non olet · About LEMON Manuals