Handles, Locks, Latches & Entry Systems: PDM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B108F:23 | Cabin Lock/Unlock Switch: Signal Stuck Low | GO to Pinpoint Test J |
| B1164:11 | Right Mirror Heater Output: Circuit Short To Ground | REFER to: Rear View Mirrors . |
| B1164:15 | Right Mirror Heater Output: Circuit Short To Battery or Open | REFER to: Rear View Mirrors . |
| B1C11:11 | Passenger Left/Right Mirror Motor: Circuit Short To Ground | REFER to: Rear View Mirrors . |
| B1C11:15 | Passenger Left/Right Mirror Motor: Circuit Short To Battery or Open | REFER to: Rear View Mirrors . |
| B1C12:11 | Passenger Up/Down Mirror Motor: Circuit Short To Ground | REFER to: Rear View Mirrors . |
| B1C12:15 | Passenger Up/Down Mirror Motor: Circuit Short To Battery or Open | REFER to: Rear View Mirrors . |
| B1C15:11 | Passenger Up/Down Mirror Motor Feedback: Circuit Short To Ground | REFER to: Rear View Mirrors . |
| B1C15:15 | Passenger Up/Down Mirror Motor Feedback: Circuit Short To Battery or Open | REFER to: Rear View Mirrors . |
| B1C16:11 | Passenger Left/Right Mirror Motor Feedback: Circuit Short To Ground | REFER to: Rear View Mirrors . |
| B1C16:15 | Passenger Left/Right Mirror Motor Feedback: Circuit Short To Battery or Open | REFER to: Rear View Mirrors . |
| B1D07:11 | Right Turn Indicator: Circuit Short To Ground | REFER to: Turn Signal and Hazard Lamps . |
| C1B15:11 | Sensor Supply Voltage B: Circuit Short To Ground | REFER to: Rear View Mirrors . |
| C1B15:15 | Sensor Supply Voltage B: Circuit Short To Battery or Open | REFER to: Rear View Mirrors . |
| U0010:00 | Medium Speed CAN Communication Bus: No Sub Type Information | The module was unable to communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). VERIFY the continuity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test W |
| U0208:00 | Lost Communication With "Seat Control Module A": No Sub Type Information | GO to Pinpoint Test X |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new PDM. REFER to: Passenger Door Module (PDM) . |
| U0300:4A | Internal Control Module Software Incompatibility: Incorrect Component Installed | PERFORM the PMI using as-built data. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC returns, INSTALL a new PDM. REFER to: Passenger Door Module (PDM) . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) from the BCM. REFER to: Body Control Module (BCM) . |
| U0509:00 | Invalid Data Received From "Seat Control Module A": No Sub Type Information | RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) from the DSM. REFER to: FRONT SEATS . |
| U2002:24 | Switch: Signal Stuck High | REFER to: Glass, Frames and Mechanisms . |
| U2010:00 | Switch Illumination: No Sub Type Information | REFER to: Instrument Panel and Interior Switches Illumination . |
| U2014:00 | Control Module Hardware: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC returns, INSTALL a new PDM. REFER to: Passenger Door Module (PDM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PERFORM the PMI using as-built data. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC returns, INSTALL a new PDM. REFER to: Passenger Door Module (PDM) . |
| U3000:04 | Control Module: System Internal Failure | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC returns, INSTALL a new PDM. REFER to: Passenger Door Module (PDM) . |