Information System And Entertainment System Touchscreen Display: ACM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1142:27 | Ignition Status 1: Signal Rate of Change Above Threshold | GO to Pinpoint Test I |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | If DTC B1A56:21 sets after running the bezel diagnostic tests, DISREGARD this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency, the test will fail. |
| B1A89:11 | Satellite Antenna: Circuit Short To Ground | For a satellite radio concern, GO to Pinpoint Test C For a SIRIUS Data Services concern, GO to Pinpoint Test D |
| B1A89:13 | Satellite Antenna: Circuit Open | For a satellite radio concern, GO to Pinpoint Test C For a SIRIUS Data Services concern, GO to Pinpoint Test D |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM. REFER to: Audio Front Control Module (ACM) . |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTC. This is normal operation. |
| U0100:00 | Lost Communication With ECM/ PCM "A": No Sub Type Information | GO to Pinpoint Test AO |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AP |
| U0142:00 | Lost Communication With Body Control Module "B": No Sub Type Information | GO to Pinpoint Test AQ |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| U0237:00 | Lost Communication With Digital Audio Control Module "C": No Sub Type Information | GO to Pinpoint Test AW |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to Pinpoint Test AX |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AY |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AZ |
| U0257:00 | Lost Communication With Front Controls / Display Interface Module: No Sub Type Information |
NOTE:
Despite the description, this DTC applies to the FDIM, not the FCDIM. GO to Pinpoint Test BA |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to an incorrect or incomplete ACM configuration. Using a diagnostic scan tool, PERFORM the ACM programming procedure using as-built data. For information on as-built data, REFER to: Module Configuration - System Operation and Component Description . See As-Built Data. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to an incorrect or incomplete ACM configuration. Using a diagnostic scan tool, PERFORM the ACM programming procedure using as-built data. For information on as-built data, REFER to: Module Configuration - System Operation and Component Description . See As-Built Data. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to an incorrect or incomplete ACM configuration. Using a diagnostic scan tool, PERFORM the ACM programming procedure using as-built data. For information on as-built data, REFER to: Module Configuration - System Operation and Component Description . See As-Built Data. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the ACM self-test. If DTC U3000:41 is retrieved again, INSTALL a new ACM. REFER to: Audio Front Control Module (ACM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR all Continuous Memory Diagnostic Trouble Codes (CMDTCs). WAIT at least 10 seconds. RETRIEVE all Continuous Memory Diagnostic Trouble Codes (CMDTCs). If DTC U3000:42 is retrieved again, INSTALL a new ACM. REFER to: Audio Front Control Module (ACM) . |
| U3000:96 | Control Module: Component Internal Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the ACM self-test. If DTC U3000:96 is retrieved again, INSTALL a new ACM. REFER to: Audio Front Control Module (ACM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BB |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BC |