Automatic Transaxle DTCS
NOTE:
Before performing a self-test, turn the vehicle off and wait 20 seconds.
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| P0297:94 | Vehicle Overspeed Condition: Unexpected Operation | This DTC sets if the motor speed exceeds 10, 000 rpm. CLEAR the DTC. REPEAT the self-test. RETURN the vehicle to the customer with information about the DTC. |
| P0560:16 | System Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test B |
| P0560:17 | System Voltage: Circuit Voltage Above Threshold | The DC to DC converter regulates voltage to the low voltage system. DIAGNOSE other TCM and PCM DTCs first. |
| P0604:42 | Internal Control Module Random Access Memory (RAM) Error: General Memory Failure | This DTC indicates the TCM RAM has been corrupted. REPROGRAM the calibration. CHECK for other DTCs or drive symptoms for further action. If DTC P0604:42 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0605:42 | Internal Control Module Read Only Memory (ROM) Error: General Memory Failure | This DTC indicates the TCM ROM has been corrupted. REPROGRAM the calibration. CHECK for other DTCs or drive symptoms for further action. If DTC P0605:42 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P060A:01 | Internal Control Module Monitoring Processor Performance: General Electrical Failure | This DTC sets if any one of the AC phase currents exceeds 675A for 250 milliseconds. CLEAR the DTC. REPEAT the self-test. If DTC P060A:01 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P060A:02 | Internal Control Module Monitoring Processor Performance: General Signal Failure | This DTC sets if there is an internal resolver issue during a commanded active discharge. CLEAR the DTC. REPEAT the self-test. If DTC P060A:02 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P060A:04 | Internal Control Module Monitoring Processor Performance: System Internal Failure | This DTC sets if the internal current sensor VREF (reference voltage) offset exceeds 5A. CLEAR the DTC. REPEAT the self-test. If DTC P060A:04 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P060B:02 | Internal Control Module A/D Processing Performance: General Signal Failure | This DTC sets if the A/D HV voltage rationality test or inverter enable rationality test fails. CLEAR the DTC. REPEAT the self-test. If DTC P060B:02 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P061B:1D | Internal Control Module Torque Calculation Performance: Circuit Current Out of Range | This DTC sets if the internal current sensor VREF (reference voltage) offset exceeds 5A. CLEAR the DTC. REPEAT the self-test. If DTC P061B:1D returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P061B:1F | Internal Control Module Torque Calculation Performance: Circuit Intermittent | This DTC sets if the TCM fails an internal quadrant and plausibility check. CLEAR the DTC. REPEAT the self-test. If DTC P061B:1F returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P062F:42 | Internal Control Module EEPROM Error: General Memory Failure | This DTC sets if the TCM EEPROM check fails. CLEAR the DTC. REPEAT the self-test. If DTC P062F:42 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0A3F:00 | Drive Motor "A" Position Sensor Circuit | This DTC sets if the TCM detects an internal resolver monitor channel fault. CLEAR the DTC. REPEAT the self-test. If DTC P0A3F:00 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0A3F:01 | Drive Motor "A" Position Sensor Circuit: General Electrical Failure | This DTC sets if the TCM detects an internal resolver signal degradation. CLEAR the DTC. REPEAT the self-test. If DTC P0A3F:01 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0A3F:02 | Drive Motor "A" Position Sensor Circuit: General Signal Failure | This DTC sets if the TCM detects an internal resolver tracking loss. CLEAR the DTC. REPEAT the self-test. If DTC P0A3F:02 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0A3F:08 | Drive Motor "A" Position Sensor Circuit: Bus Signal / Message Failure | This DTC sets if the TCM detects an internal resolver signal failure. CLEAR the DTC. REPEAT the self-test. If DTC P0A3F:08 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0A3F:1F | Drive Motor "A" Position Sensor Circuit: Circuit Intermittent | This DTC sets if the TCM detects an intermittent signal from the internal resolver. CLEAR the DTC. REPEAT the self-test. If DTC P0A3F:1F returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0A78:17 | Drive Motor "A" Inverter Performance: Circuit Voltage Above Threshold | This DTC sets if the TCM detects excessive inverter voltage. CLEAR the DTC. REPEAT the self-test. If DTC P0A78:17 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0A78:49 | Drive Motor "A" Inverter Performance: Internal Electronic Failure | This DTC sets if the TCM inverter fails an internal line switching test. CLEAR the DTC. REPEAT the self-test. If DTC P0A78:49 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0A90:46 | Drive Motor "A" Performance: Calibration / Parameter Memory Failure | This DTC sets if the TCM internal resolver stored offset does not match the actual measured offset. CLEAR the DTC. REPEAT the self-test. If DTC P0A90:46 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0AED:11 | Drive Motor Inverter Temperature Sensor "A" Circuit: Circuit Short To Ground | This DTC sets if the TCM detects an internal temperature sensor signal dropping below 0.3v. CLEAR the DTC. REPEAT the self-test. If DTC P0AED:11 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0AED:15 | Drive Motor Inverter Temperature Sensor "A" Circuit: Circuit Short To Battery or Open | This DTC sets if the TCM detects an internal temperature sensor signal rising above 2.9v when any motor phase exceeds 50A for 30 seconds or 200 amps for 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC P0AED:15 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0AED:1C | Drive Motor Inverter Temperature Sensor "A" Circuit: Circuit Voltage Out of Range | This DTC sets if the TCM detects an internal temperature sensor signal out of range. CLEAR the DTC. REPEAT the self-test. If DTC P0AED:1C returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0AED:1F | Drive Motor Inverter Temperature Sensor "A" Circuit: Circuit Intermittent | This DTC sets if the TCM detects an intermittent internal temperature sensor signal. CLEAR the DTC. REPEAT the self-test. If DTC P0AED:1F returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0AED:98 | Drive Motor Inverter Temperature Sensor "A" Circuit: Component or System Over Temperature | This DTC sets if the TCM detects excessive internal temperature. CLEAR the DTC. REPEAT the self-test. If DTC P0AED:98 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0AF8:16 | Hybrid/EV Battery System Voltage: Circuit Voltage Below Threshold | This DTC sets if the TCM detects that the high voltage DC (HVDC) system voltage is less than 190v. CLEAR the DTC. REPEAT the self-test. If DTC P0AF8:16 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0AFB:17 | Hybrid/EV Battery System Voltage High: Circuit Voltage Above Threshold | This DTC sets if the TCM detects that the high voltage DC (HVDC) system voltage is greater than 390v. CLEAR the DTC. REPEAT the self-test. The possible causes are the TCM or the high voltage wiring harness. If DTC P0AFB:17 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0AFB:1C | Hybrid/EV Battery System Voltage High: Circuit Voltage Out of Range | This DTC sets if the TCM detects that the high voltage DC (HVDC) system voltage is out of range. CLEAR the DTC. REPEAT the self-test. The possible causes are the TCM or the high voltage wiring harness. If DTC P0AFB:1C returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0B3D:16 | Hybrid/EV Battery Voltage Sense "A" Circuit Low: Circuit Voltage Below Threshold | This DTC sets if the TCM internal 25v supply voltage drops below 18v. CLEAR the DTC. REPEAT the self-test. If DTC P0B3D:16 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0B3D:1C | Hybrid/EV Battery Voltage Sense "A" Circuit Low: Circuit Voltage Out of Range | This DTC sets if the TCM internal 5v supply voltage drops below 4.5v. CLEAR the DTC. REPEAT the self-test. If DTC P0B3D:1C returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0B3D:1F | Hybrid/EV Battery Voltage Sense "A" Circuit Low: Circuit Intermittent | This DTC sets if the TCM internal 0.5 volt sensor is operating intermittently. CLEAR the DTC. REPEAT the self-test. If DTC P0B3D:1F returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0B3E:17 | Hybrid/EV Battery Voltage Sense "A" Circuit High: Circuit Voltage Above Threshold | This DTC sets if the TCM internal 25v supply voltage rises above 26.25v. CLEAR the DTC. REPEAT the self-test. If DTC P0B3E:17 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0B3E:1C | Hybrid/EV Battery Voltage Sense "A" Circuit High: Circuit Voltage Out of Range | This DTC sets if the TCM internal 5v supply voltage rises above 5.5v. CLEAR the DTC. REPEAT the self-test. If DTC P0B3E:1C returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0B3E:1F | Hybrid/EV Battery Voltage Sense "A" Circuit High: Circuit Intermittent | This DTC sets if the TCM internal 1.5 volt sensor is operating intermittently. CLEAR the DTC. REPEAT the self-test. If DTC P0B3D:1F returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0BFD:1D | Drive Motor "A" Phase U-V-W Current Sensor Correlation: Circuit Current Out of Range | This DTC sets if the TCM internal phase current sensors do not correlate. CLEAR the DTC. REPEAT the self-test. If DTC P0BFD:1D returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0BFD:1F | Drive Motor "A" Phase U-V-W Current Sensor Correlation: Circuit Intermittent | This DTC sets if the TCM internal phase current sensors do not correlate. CLEAR the DTC. REPEAT the self-test. If DTC P0BFD:1F returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0C05:1D | Drive Motor "A" Phase U-V-W Circuit/Open: Circuit Current Out of Range | This DTC sets if the TCM detects an open motor phase. CLEAR the DTC. REPEAT the self-test. The possible causes are the TCM or the high voltage wiring harness. If DTC P0C05:1D returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0C07:19 | Drive Motor "A" Phase U-V-W Circuit High: Circuit Current Above Threshold | This DTC sets if the TCM detects any motor phase current exceeding 650A. CLEAR the DTC. REPEAT the self-test. The possible causes are the TCM or the high voltage wiring harness. If DTC P0C07:19 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0CBC:11 | Drive Motor "A" Coolant Temperature Sensor Circuit: Circuit Short To Ground | This DTC sets if the TCM detects less than 0.15v on either motor coolant sensor signal circuit. CLEAR the DTC. REPEAT the self-test. If DTC P0CBC:11 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0CBC:15 | Drive Motor "A" Coolant Temperature Sensor Circuit: Circuit Short To Battery or Open | This DTC sets if the TCM detects more than 2.97v on either motor coolant sensor signal circuit. CLEAR the DTC. REPEAT the self-test. If DTC P0CBC:15 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P0CBD:17 | Drive Motor "A" Coolant Temperature Sensor Circuit Range/Performance: Circuit Voltage Above Threshold | This DTC sets if the TCM detects more than 155 °C on either motor coolant sensor signal circuit. CLEAR the DTC. REPEAT the self-test. If DTC P0CBD:17 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P1601:02 | ECM/TCM Serial Communication Error: General Signal Failure | This DTC sets if the TCM fails the PCM rationality check. CLEAR the DTC. REPEAT the self-test. If DTC P1601:02 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P1608:1F | Watchdog Malfunction: Circuit Intermittent | This DTC sets if the TCM indicates a watchdog failure. CLEAR the DTC. REPEAT the self-test. If DTC P1608:1F returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P1627:01 | Module Supply Voltage Out Of Range: General Electrical Failure | This DTC sets if the TCM internal VREF (reference voltage) drops below or exceeds a calibrated value. CLEAR the DTC. REPEAT the self-test. If DTC P1627:01 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P1627:02 | Module Supply Voltage Out Of Range: General Signal Failure | This DTC sets if the TCM internal VREF (reference voltage) drops below or exceeds a calibrated value. CLEAR the DTC. REPEAT the self-test. If DTC P1627:02 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P1627:1C | Module Supply Voltage Out Of Range: Circuit Voltage Out of Range | This DTC sets if the TCM internal VREF (reference voltage) drops below or exceeds a calibrated value. CLEAR the DTC. REPEAT the self-test. If DTC P1627:1C returns, INSTALL a new TCM. Refer to: Electric Motor . |
| P1A0A:01 | Immediate Shutdown Signal A: General Electrical Failure | GO to Pinpoint Test A |
| P1A0A:17 | Immediate Shutdown Signal A: Circuit Voltage Above Threshold | GO to Pinpoint Test A |
| P1A0A:18 | Immediate Shutdown Signal A: Circuit Current Below Threshold | GO to Pinpoint Test A |
| P1A0A:29 | Immediate Shutdown Signal A: Signal Invalid | GO to Pinpoint Test A |
| B10D6:51 | PATS Enable Status: Not Programmed | This DTC sets if the TCM indicates the PATS configuration is incomplete. CLEAR the DTC. REPEAT the self-test. If DTC B10D6:51 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| U0100:00 | Lost Communication With ECM/PCM "A" | REFER to: Communications Network . |
| U0111:00 | Lost Communication With Battery Energy Control Module "A" | REFER to: Communications Network . |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module | REFER to: Communications Network . |
| U0140:00 | Lost Communication With Body Control Module | REFER to: Communications Network . |
| U0298:00 | Lost Communication With DC to DC Converter Control Module "A" | REFER to: Communications Network . |
| U0300:00 | Internal Control Module Software Incompatibility | This DTC sets if the TCM fails an internal software components compatibility check. CLEAR the DTC. REPEAT the self-test. If DTC U0300:00 returns, INSTALL a new TCM. Refer to: Electric Motor . |
| U0401:00 | Invalid Data Received from ECM/PCM A | REFER to: Communications Network . |
| U0418:00 | Invalid Data Received From Brake System Control Module | REFER to: Communications Network . |
| U0422:00 | Invalid Data Received From Body Control Module | REFER to: Communications Network . |
| U0426:00 | Invalid Data Received From Vehicle Immobilizer Control Module | Diagnose all non-network DTCs set in the BCM or RFA module. For BCMREFER to: Body Control Module (BCM) . For RFAREFER to: Remote Function Actuator (RFA) Module . |
| U1012:00 | Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module | REFER to: Communications Network . |
| U1A14:09 | CAN Initialization Failure: Component Failure | This DTC sets if the TCM fails to initialize its internal CAN hardware. CLEAR the DTC. REPEAT the self-test. If DTC U1A14:09 returns, INSTALL a new TCM. Refer to: Electric Motor . |