Driver Door Module (DDM) DTC Table
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1088:83 | LIN Bus "B": Value of Signal Protection Calculation Incorrect | GO to Pinpoint Test C |
| B1088:87 | LIN Bus "B": Missing Message | GO to Pinpoint Test C |
| B117C:07 | Rear Power Window Up: Mechanical Failure | INITIALIZE the LH rear door window regulator motor. REFER to: Power Door Window Initialization . |
| B117C:16 | Rear Power Window Up: Circuit Voltage Below Threshold | GO to Pinpoint Test F |
| B117C:4B | Rear Power Window Up: Over Temperature | WAIT 10 minutes to allow the window motor to cool. INITIALIZE the LH rear door window regulator motor. REFER to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B117C:92 | Rear Power Window Up: Performance or Incorrect Operation | INITIALIZE the LH rear door window regulator motor. REFER to: Power Door Window Initialization . |
| B117E:07 | Front Power Window Up: Mechanical Failure | INITIALIZE the driver door window regulator motor. REFER to: Power Door Window Initialization . |
| B117E:16 | Front Power Window Up: Circuit Voltage Below Threshold | GO to Pinpoint Test C |
| B117E:4B | Front Power Window Up: Over Temperature | WAIT 10 minutes to allow the window motor to cool. INITIALIZE the driver door window regulator motor. REFER to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B117E:92 | Front Power Window Up: Performance or Incorrect Operation | INITIALIZE the driver door window regulator motor. REFER to: Power Door Window Initialization . |
| B1189:11 | Front Window Position Sensor: Circuit Short To Ground | GO to Pinpoint Test C |
| B1189:16 | Front Window Position Sensor: Voltage Below Threshold | GO to Pinpoint Test C |
| B1189:17 | Front Window Position Sensor: Voltage Above Threshold | GO to Pinpoint Test C |
| B1189:29 | Front Window Position Sensor: Signal Invalid | GO to Pinpoint Test C |
| B1189:2B | Front Window Position Sensor: Signal Cross Coupled | GO to Pinpoint Test C |
| B1189:39 | Front Window Position Sensor: Signal Has Too Few Pulses | GO to Pinpoint Test C |
| B1189:3A | Front Window Position Sensor: Signal Has Too Many Pulses | GO to Pinpoint Test C |
| B1189:65 | Front Window Position Sensor: Has Too Few Transitions / Events | GO to Pinpoint Test C |
| B1189:77 | Front Window Position Sensor: Commanded Position Not Reachable | DIAGNOSE all other Diagnostic Trouble Codes (DTCs) first. If no other Diagnostic Trouble codes (DTCs) are present, INITIALIZE the LH front door window regulator motor. REFER to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B118A:11 | Rear Window Position Sensor: Circuit Short To Ground | GO to Pinpoint Test F |
| B118A:16 | Rear Window Position Sensor: Voltage Below Threshold | GO to Pinpoint Test F |
| B118A:17 | Rear Window Position Sensor: Voltage Above Threshold | GO to Pinpoint Test F |
| B118A:29 | Rear Window Position Sensor: Signal Invalid | GO to Pinpoint Test F |
| B118A:2B | Rear Window Position Sensor: Signal Cross Coupled | GO to Pinpoint Test F |
| B118A:39 | Rear Window Position Sensor: Signal Has Too Few Pulses | GO to Pinpoint Test F |
| B118A:3A | Rear Window Position Sensor: Signal Has Too Many Pulses | GO to Pinpoint Test F |
| B118A:65 | Rear Window Position Sensor: Has Too Few Transitions / Events | GO to Pinpoint Test F |
| B118A:77 | Rear Window Position Sensor: Commanded Position Not Reachable | DIAGNOSE all other Diagnostic Trouble Codes (DTCs) first. If no other Diagnostic Trouble codes (DTCs) are present, INITIALIZE the LH rear door window regulator motor. REFER to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B12C5:71 | Front Window Lifter Motor Up Relay: Actuator Stuck | GO to Pinpoint Test C |
| B12C6:71 | Rear Window Lifter Motor Up Relay: Actuator Stuck | GO to Pinpoint Test F |
| B12C7:71 | Rear Window Lifter Motor Down Relay: Actuator Stuck | GO to Pinpoint Test F |
| B12C8:71 | Front Window Lifter Motor Down Relay: Actuator Stuck | GO to Pinpoint Test C |
| B12E9:23 | Rear Window Local Up/Down Switch: Signal Stuck Low | GO to Pinpoint Test F |
| B12E9:24 | Rear Window Local Up/Down Switch: Signal Stuck High | GO to Pinpoint Test F |
| B13F0:4B | Left Rear Power Window Motor: Over Temperature | CLEAR the DTC. WAIT 10 minutes to allow the window motor to cool. INITIALIZE the LH rear door window regulator motor. REFER to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B13F1:4B | Driver Power Window Motor: Over Temperature | CLEAR the DTC. WAIT 10 minutes to allow the window motor to cool. INITIALIZE the driver door window regulator motor. REFER to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| C1B14:11 | Sensor Supply Voltage A: Circuit Short To Ground | GO to Pinpoint Test C |
| C1B14:15 | Sensor Supply Voltage A: Circuit Short To Battery or Open | GO to Pinpoint Test C |
| C1B14:16 | Sensor Supply Voltage A: Circuit Voltage Below Threshold | GO to Pinpoint Test C |
| C1B14:17 | Sensor Supply Voltage A: Circuit Voltage Above Threshold | GO to Pinpoint Test C |
| C1B1A:11 | Sensor Supply Voltage C: Circuit Short To Ground | GO to Pinpoint Test F |
| C1B1A:15 | Sensor Supply Voltage C: Circuit Short To Battery or Open | GO to Pinpoint Test F |
| C1B1A:16 | Sensor Supply Voltage C: Circuit Voltage Below Threshold | GO to Pinpoint Test F |
| C1B1A:17 | Sensor Supply Voltage C: Circuit Voltage Above Threshold | GO to Pinpoint Test F |
| U2013:24 | Switch Pack: Signal Stuck High | CLEAR the DTC. TEST the system for normal operation from the driver door window control switch. If any individual switches within the driver door window control switch are inoperative or the DTC returns, INSTALL a new driver door window control switch. REFER to: Front Door Window Control Switch . |
| All other Diagnostic Trouble Codes (DTCs) | - | REFER to: Locks, Latches and Entry Systems . |