Information System And Entertainment System Am/Fm/Cd/Sync DTCS: GPSM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| U0100:00 | Lost Communication with ECM/ PCM "A": No Sub Type Information | GO to Pinpoint Test AE |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AF |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AI |
| U0401:00 | Invalid Data Received from ECM/ PCM A: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the PCM. For vehicles with the 2.3L EcoBoost (201kW/273PS), REFER to: Electronic Engine Controls . For vehicles with the 3.7L Duratec (227kW/301PS), REFER to: Electronic Engine Controls . For vehicles with the 5.0L 32V Ti-VCT, REFER to: Electronic Engine Controls . For vehicles with the 5.2L, REFER to: Electronic Engine Controls .
NOTE:
If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom.
|
| U0422:00 | Invalid Data Received from Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the BCM. Refer to: Body Control Module (BCM) .* If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC. Refer to: Instrumentation, Message Center and Warning Chimes .* If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to an incorrect or incomplete GPSM configuration. Using a diagnostic scan tool, PERFORM the GPSM programming procedure using as-built data. For information on as-built data, REFER to: Module Configuration - System Operation and Component Description . See As-Built Data. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to an incorrect or incomplete GPSM configuration. Using a diagnostic scan tool, PERFORM the GPSM programming procedure using as-built data. For information on as-built data, REFER to: Module Configuration - System Operation and Component Description . See As-Built Data. |
| U3000:09 | Control Module: Component Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:09 is retrieved again, DISCONNECT the battery for 1 minute, then reconnect it. CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:09 is retrieved again, INSTALL a new GPSM. Refer to: Global Positioning System Module (GPSM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new GPSM. Refer to: Global Positioning System Module (GPSM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new GPSM. Refer to: Global Positioning System Module (GPSM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AQ |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AR |