Moveable Roof Control Module B (MRCMB)
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1070:12 | Tonneau Lid Piston Out Sensor: Circuit Short to Battery | GO to Pinpoint Test B |
| B1070:14 | Tonneau Lid Piston Out Sensor: Circuit Short to Ground or Open | GO to Pinpoint Test B |
| B1070:29 | Tonneau Lid Piston Out Sensor: Signal Invalid | GO to Pinpoint Test B |
| B1268:24 | Convertible / Folding Top Activation Down Switch: Signal Stuck High | GO to Pinpoint Test E |
| P0604:44 | Internal Control Module Random Access Memory (RAM) Error: Data Memory Failure | Using a diagnostic scan tool, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. CARRY OUT the Moveable Roof Control Module B (MRCMB) self-test. If the DTC returns, INSTALL a new Moveable Roof Control Module B (MRCMB). Refer to: Convertible Top Motor . |
| P0605:45 | Internal Control Module Read Only Memory (ROM) Error: Program Memory Failure | Using a diagnostic scan tool, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. CARRY OUT the Moveable Roof Control Module B (MRCMB) self-test. If the DTC returns, INSTALL a new Moveable Roof Control Module B (MRCMB). Refer to: Convertible Top Motor . |
| P062F:46 | Internal Control Module EEPROM Error: Calibration / Parameter Memory Failure | Using a diagnostic scan tool, CLEAR the DTC. SET the ignition to OFF and wait 20 seconds. SET the ignition to ON. CARRY OUT the Moveable Roof Control Module B (MRCMB) self-test. If the DTC returns, INSTALL a new Moveable Roof Control Module B (MRCMB). Refer to: Convertible Top Motor . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test F |
| U0207:00 | Lost Communication With Moveable Roof Control Module "A" (MRCMA): No Sub Type Information | GO to Pinpoint Test J |
| U2011:64 | Motor: Signal Plausibility Failure | Using a diagnostic scan tool, CLEAR the DTC. SET the ignition to ON. Using the convertible top switch, OPEN or CLOSE the convertible top. If the convertible top does not operate, INSTALL a new Moveable Roof Control Module B (MRCMB). Refer to: Convertible Top Motor . |
| U2011:98 | Motor: Component or System Over Temperature | WAIT a minimum of 2 minutes to allow the motor time to cool. Using a diagnostic scan tool, CLEAR the DTC. SET the ignition to ON. Using the convertible top switch, OPEN or CLOSE the convertible top. If the convertible top does not operate, CARRY OUT the Moveable Roof Control Module B (MRCMB) self-test. If the DTC does not return, DIAGNOSE any other Moveable Roof Control Module B (MRCMB) Diagnostic Trouble Codes (DTCs), verify all convertible roof operation entry conditions have been met. Refer to: Convertible Top - Overview . If the DTC returns, the system has not had sufficient time to cool. SET the ignition to OFF and WAIT another 2 minutes, CLEAR the DTC and REPEAT the self-test. |
| U2013:64 | Switch Pack: Signal Plausibility Failure | GO to Pinpoint Test E |
| U3000:49 | Control Module: Internal Electronic Failure | Using a diagnostic scan tool, CLEAR the DTC. SET the ignition to ON. Using the convertible top switch, OPEN or CLOSE the convertible top. Using a diagnostic scan tool, CARRY OUT the Moveable Roof Control Module B (MRCMB) self-test. If the DTC returns, INSTALL a new Moveable Roof Control Module B (MRCMB). Refer to: Convertible Top Motor . |