Information System And Entertainment System Am/Fm/Cd/Sync DTCS: APIM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1252:04 | USB Port: System Internal Failure | GO to Pinpoint Test U |
| B1252:11 | USB Port: Circuit Short To Ground | GO to Pinpoint Test U |
| B12B8:04 | USB Port #2: System Internal Failure | GO to Pinpoint Test V |
| B12B8:11 | USB Port #2: Circuit Short To Ground | GO to Pinpoint Test V |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to Pinpoint Test S |
| B1D79:11 | Microphone Input: Circuit Short To Ground | GO to Pinpoint Test S |
| B1D79:12 | Microphone Input: Circuit Short To Battery | GO to Pinpoint Test S |
| B1D79:13 | Microphone Input: Circuit Open | GO to Pinpoint Test S |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AF |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AH |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AI |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to Pinpoint Test AK |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AL |
| U0257:00 | Lost Communication With Front Controls / Display Interface Module: No Sub Type Information | GO to Pinpoint Test AP |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the BCM. Refer to: Body Control Module (BCM) .* If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC. Refer to: Instrumentation, Message Center and Warning Chimes .* If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom. |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the RCM. Refer to: Airbag Supplemental Restraint System (SRS) .* If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to an incorrect or incomplete APIM programming/provisioning. Using a diagnostic scan tool, PERFORM the APIM programming procedure. Refer to: SYNC Module [APIM] Programming . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to an incorrect or incomplete APIM programming/provisioning. Using a diagnostic scan tool, PERFORM the APIM programming procedure. Refer to: SYNC Module [APIM] Programming . |
| U3000:04 | Control Module: System Internal Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:04 is retrieved again, PERFORM the APIM Hardware Test. Refer to APIM Hardware Testing . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, PERFORM the APIM Hardware Test. Refer to APIM Hardware Testing . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, PERFORM the APIM Hardware Test. Refer to APIM Hardware Testing . |
| U3000:88 | Control Module: Bus Off |
NOTE:
The module was unable to communicate on the network at a point in time. The fault is not currently present since the module had to communicate with the diagnostic scan tool to report this DTC. To avoid repeat network concerns: INSPECT for damaged or corroded wiring at the APIM. Refer to Module Communications Network
for schematic and connector information.CLEAR the DTC.WAIT at least 10 seconds.REPEAT the network test with the diagnostic scan tool. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AQ |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AR |