Restraint Control Module (RCM)
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. For information about these practices, REFER to: Diagnostic Methods .
NOTE:
Unlisted Diagnostic Trouble Codes (DTCs) are often retrieved as a result of incorrect repair procedures. Before attempting any repairs for unlisted Diagnostic Trouble Codes (DTCs), check the vehicle service history for recent repairs. For RCM Diagnostic Trouble Codes (DTCs) not listed in this chart,
- Repair all other RCM Diagnostic Trouble Codes (DTCs) before attempting to repair any Diagnostic Trouble Codes (DTCs) not listed in this chart.
- If no other RCM Diagnostic Trouble Codes (DTCs) are retrieved, CLEAR the RCM Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the RCM Diagnostic Trouble Codes (DTCs) return, VERIFY that the RCM is the correct part number for the vehicle application, and INSTALL As-Built data following scan tool instructions under Module Programming > As-Built.
- Inspect the RCM and RCM connectors for any damaged pins or connections.
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B0001:11 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: A . |
| B0001:12 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: A . |
| B0001:13 | Driver Frontal Stage 1 Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: A . |
| B0001:1A | Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: A . |
| B0001:2B | Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0001:4A | Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0002:11 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: B . |
| B0002:12 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: B . |
| B0002:13 | Driver Frontal Stage 2 Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: B . |
| B0002:1A | Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: B . |
| B0002:2B | Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0002:4A | Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0004:11 | Driver Knee Bolster Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: C . |
| B0004:12 | Driver Knee Bolster Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: C . |
| B0004:13 | Driver Knee Bolster Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: C . |
| B0004:1A | Driver Knee Bolster Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: C . |
| B0004:2B | Driver Knee Bolster Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0004:4A | Driver Knee Bolster Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0005:11 | Collapsible Steering Column Deployment Control: Circuit Short to Ground | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0005:12 | Collapsible Steering Column Deployment Control: Circuit Short to Battery | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0005:13 | Collapsible Steering Column Deployment Control: Circuit Open | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0005:1A | Collapsible Steering Column Deployment Control: Circuit Resistance Below Threshold | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0005:2B | Collapsible Steering Column Deployment Control: Signal Cross Coupled | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0005:4A | Collapsible Steering Column Deployment Control: Incorrect Component Installed | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0010:11 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: D . |
| B0010:12 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: D . |
| B0010:13 | Passenger Frontal Stage 1 Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: D . |
| B0010:1A | Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: D . |
| B0010:2B | Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0010:4A | Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0011:11 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: E . |
| B0011:12 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: E . |
| B0011:13 | Passenger Frontal Stage 2 Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: E . |
| B0011:1A | Passenger Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: E . |
| B0011:2B | Passenger Frontal Stage 2 Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0011:4A | Passenger Frontal Stage 2 Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0013:11 | Passenger Knee Bolster Deployment Control: Circuit Short to Ground | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0013:12 | Passenger Knee Bolster Deployment Control: Circuit Short to Battery | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0013:13 | Passenger Knee Bolster Deployment Control: Circuit Open | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0013:1A | Passenger Knee Bolster Deployment Control: Circuit Resistance Below Threshold | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0013:2B | Passenger Knee Bolster Deployment Control: Signal Cross Coupled | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0013:4A | Passenger Knee Bolster Deployment Control: Incorrect Component Installed | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0020:11 | Left Side Airbag Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: F . |
| B0020:12 | Left Side Airbag Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: F . |
| B0020:13 | Left Side Airbag Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: F . |
| B0020:1A | Left Side Airbag Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: F . |
| B0020:2B | Left Side Airbag Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0020:4A | Left Side Airbag Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0021:11 | Left Curtain Deployment Control 1: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: G . |
| B0021:12 | Left Curtain Deployment Control 1: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: G . |
| B0021:13 | Left Curtain Deployment Control 1: Circuit Open | REFER to: Pinpoint Test - DTC: G . |
| B0021:1A | Left Curtain Deployment Control 1: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: G . |
| B0021:2B | Left Curtain Deployment Control 1: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0021:4A | Left Curtain Deployment Control 1: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0028:11 | Right Side Airbag Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: H . |
| B0028:12 | Right Side Airbag Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: H . |
| B0028:13 | Right Side Airbag Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: H . |
| B0028:1A | Right Side Airbag Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: H . |
| B0028:2B | Right Side Airbag Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0028:4A | Right Side Airbag Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0029:11 | Right Curtain Deployment Control 1: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: I . |
| B0029:12 | Right Curtain Deployment Control 1: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: I . |
| B0029:13 | Right Curtain Deployment Control 1: Circuit Open | REFER to: Pinpoint Test - DTC: I . |
| B0029:1A | Right Curtain Deployment Control 1: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: I . |
| B0029:2B | Right Curtain Deployment Control 1: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0029:4A | Right Curtain Deployment Control 1: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0050:11 | Driver Seatbelt Sensor: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: J . |
| B0050:12 | Driver Seatbelt Sensor: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: J . |
| B0050:13 | Driver Seatbelt Sensor: Circuit Open | REFER to: Pinpoint Test - DTC: J . |
| B0050:1D | Driver Seatbelt Sensor: Circuit Current Out of Range | REFER to: Pinpoint Test - DTC: J . |
| B0050:2B | Driver Seatbelt Sensor: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0050:4A | Driver Seatbelt Sensor: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0052:11 | Passenger Seatbelt Sensor: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: K . |
| B0052:12 | Passenger Seatbelt Sensor: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: K . |
| B0052:13 | Passenger Seatbelt Sensor: Circuit Open | REFER to: Pinpoint Test - DTC: K . |
| B0052:1D | Passenger Seatbelt Sensor: Circuit Current Out of Range | REFER to: Pinpoint Test - DTC: K . |
| B0052:2B | Passenger Seatbelt Sensor: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0052:4A | Passenger Seatbelt Sensor: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0080:11 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short to Ground | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0080:12 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short to Battery | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0080:13 | Driver Seatbelt Load Limiter Deployment Control: Circuit Open | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0080:1A | Driver Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0080:2B | Driver Seatbelt Load Limiter Deployment Control: Signal Cross Coupled | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0080:4A | Driver Seatbelt Load Limiter Deployment Control: Incorrect Component Installed | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B0082:11 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: L . |
| B0082:12 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: L . |
| B0082:13 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: L . |
| B0082:1A | Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: L . |
| B0082:2B | Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0082:4A | Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0090:11 | Left Frontal Restraints Sensor: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: M . |
| B0090:2B | Left Frontal Restraints Sensor: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0090:4A | Left Frontal Restraints Sensor: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0090:81 | Left Frontal Restraints Sensor: Invalid Serial Data Received | REFER to: Pinpoint Test - DTC: M . |
| B0090:93 | Left Frontal Restraints Sensor: No Operation | REFER to: Pinpoint Test - DTC: M . |
| B0090:96 | Left Frontal Restraints Sensor: Component Internal Failure | INSTALL a new LH front impact severity sensor. REFER to: Front Impact Severity Sensor . |
| B0091:11 | Left Side Restraints Sensor 1: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: N . |
| B0091:2B | Left Side Restraints Sensor 1: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0091:4A | Left Side Restraints Sensor 1: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0091:81 | Left Side Restraints Sensor 1: Invalid Serial Data Received | REFER to: Pinpoint Test - DTC: N . |
| B0091:93 | Left Side Restraints Sensor 1: No Operation | REFER to: Pinpoint Test - DTC: N . |
| B0091:96 | Left Side Restraints Sensor 1: Component Internal Failure | INSTALL a new driver door side impact sensor. REFER to: Front Door Side Impact Sensor . |
| B0092:4A | Left Side Restraints Sensor 2: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0092:81 | Left Side Restraints Sensor 2: Invalid Serial Data Received | REFER to: Pinpoint Test - DTC: O . |
| B0092:96 | Left Side Restraints Sensor 2: Component Internal Failure | INSTALL a new LH C-pillar side impact sensor. REFER to: C-Pillar Side Impact Sensor . |
| B0095:11 | Right Frontal Restraints Sensor: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: P . |
| B0095:2B | Right Frontal Restraints Sensor: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0095:4A | Right Frontal Restraints Sensor: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0095:81 | Right Frontal Restraints Sensor: Invalid Serial Data Received | REFER to: Pinpoint Test - DTC: P . |
| B0095:93 | Right Frontal Restraints Sensor: No Operation | REFER to: Pinpoint Test - DTC: P . |
| B0095:96 | Right Frontal Restraints Sensor: Component Internal Failure | INSTALL a new RH front impact severity sensor. REFER to: Front Impact Severity Sensor . |
| B0096:11 | Right Side Restraints Sensor 1: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: O . |
| B0096:2B | Right Side Restraints Sensor 1: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B0096:4A | Right Side Restraints Sensor 1: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0096:81 | Right Side Restraints Sensor 1: Invalid Serial Data Received | REFER to: Pinpoint Test - DTC: O . |
| B0096:93 | Right Side Restraints Sensor 1: No Operation | REFER to: Pinpoint Test - DTC: O . |
| B0096:96 | Right Side Restraints Sensor 1: Component Internal Failure | INSTALL a new passenger door side impact sensor. REFER to: Front Door Side Impact Sensor . |
| B0097:4A | Right Side Restraints Sensor 2: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B0097:81 | Right Side Restraints Sensor 2: Invalid Serial Data Received | REFER to: Pinpoint Test - DTC: N . |
| B0097:96 | Right Side Restraints Sensor 2: Component Internal Failure | INSTALL a new RH C-pillar side impact sensor. REFER to: C-Pillar Side Impact Sensor . |
| B00A0:09 | Occupant Classification System: Component Failure | REFER to: Pinpoint Test - DTC: Q . |
| B00A0:4A | Occupant Classification System: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Q . |
| B00A0:63 | Occupant Classification System: Circuit / Component Protection Time-Out | REFER to: Pinpoint Test - DTC: Q . |
| B00A0:64 | Occupant Classification System: Signal Plausibility Failure | REFER to: Pinpoint Test - DTC: Q . |
| B00A0:68 | Occupant Classification System: Event Information | REFER to: Pinpoint Test - DTC: Q . |
| B00B5:11 | Driver Seat Track Position Restraints Sensor: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: R . |
| B00B5:12 | Driver Seat Track Position Restraints Sensor: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: R . |
| B00B5:13 | Driver Seat Track Position Restraints Sensor: Circuit Open | REFER to: Pinpoint Test - DTC: R . |
| B00B5:1D | Driver Seat Track Position Restraints Sensor: Circuit Current Out of Range | REFER to: Pinpoint Test - DTC: R . |
| B00B5:2B | Driver Seat Track Position Restraints Sensor: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B00B5:4A | Driver Seat Track Position Restraints Sensor: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B00C5:11 | Passenger Seat Track Position Restraints Sensor: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: S . |
| B00C5:12 | Passenger Seat Track Position Restraints Sensor: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: S . |
| B00C5:13 | Passenger Seat Track Position Restraints Sensor: Circuit Open | REFER to: Pinpoint Test - DTC: S . |
| B00C5:1D | Passenger Seat Track Position Restraints Sensor: Circuit Current Out of Range | REFER to: Pinpoint Test - DTC: S . |
| B00C5:2B | Passenger Seat Track Position Restraints Sensor: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B00C5:4A | Passenger Seat Track Position Restraints Sensor: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B00D5:12 | Restraint System Passenger Disable Indicator: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: T . |
| B00D5:14 | Restraint System Passenger Disable Indicator: Circuit Short to Ground or Open | REFER to: Pinpoint Test - DTC: T . |
| B00D5:4A | Restraint System Passenger Disable Indicator: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | This DTC indicates the vehicle has been in a crash. INSTALL a new RCM and impact sensors. REFER to: Inspection and Repair after a Supplemental Restraint System (SRS) Deployment . |
| B11CF:11 | Passenger Frontal Airbag Canister Vent: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: U . |
| B11CF:12 | Passenger Frontal Airbag Canister Vent: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: U . |
| B11CF:13 | Passenger Frontal Airbag Canister Vent: Circuit Open | REFER to: Pinpoint Test - DTC: U . |
| B11CF:1A | Passenger Frontal Airbag Canister Vent: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: U . |
| B11CF:2B | Passenger Frontal Airbag Canister Vent: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B11CF:4A | Passenger Frontal Airbag Canister Vent: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B11D8:12 | Restraint Event Notification: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: V . |
| B11D8:14 | Restraint Event Notification: Circuit Short to Ground or Open | REFER to: Pinpoint Test - DTC: V . |
| B1202:12 | Restraint System Passenger Enable Indicator: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: RR . |
| B1202:14 | Restraint System Passenger Enable Indicator: Circuit Short to Ground or Open | REFER to: Pinpoint Test - DTC: RR . |
| B1202:4A | Restraint System Passenger Enable Indicator: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B1211:11 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: X . |
| B1211:12 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: X . |
| B1211:13 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: X . |
| B1211:1A | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: X . |
| B1211:2B | Driver Seatbelt Retractor Pretensioner Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B1211:4A | Driver Seatbelt Retractor Pretensioner Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B1214:11 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: W . |
| B1214:12 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: W . |
| B1214:13 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: W . |
| B1214:1A | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: W . |
| B1214:2B | Passenger Seatbelt Retractor Pretensioner Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B1214:4A | Passenger Seatbelt Retractor Pretensioner Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B13DA:11 | Driver Seatbelt Anchor Pretensioner Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: OO . |
| B13DA:12 | Driver Seatbelt Anchor Pretensioner Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: OO . |
| B13DA:13 | Driver Seatbelt Anchor Retractor Pretensioner Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: OO . |
| B13DA:1A | Driver Seatbelt Anchor Pretensioner Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: OO . |
| B13DA:2B | Driver Seatbelt Anchor Pretensioner Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B13DA:4A | Driver Seatbelt Anchor Pretensioner Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B13DB:11 | Passenger Seatbelt Anchor Pretensioner Deployment Control: Circuit Short to Ground | REFER to: Pinpoint Test - DTC: PP . |
| B13DB:12 | Passenger Seatbelt Anchor Pretensioner Deployment Control: Circuit Short to Battery | REFER to: Pinpoint Test - DTC: PP . |
| B13DB:13 | Passenger Seatbelt Anchor Retractor Pretensioner Deployment Control: Circuit Open | REFER to: Pinpoint Test - DTC: PP . |
| B13DB:1A | Passenger Seatbelt Anchor Pretensioner Deployment Control: Circuit Resistance Below Threshold | REFER to: Pinpoint Test - DTC: PP . |
| B13DB:2B | Passenger Seatbelt Anchor Pretensioner Deployment Control: Signal Cross Coupled | REFER to: Pinpoint Test - DTC: Y . |
| B13DB:4A | Passenger Seatbelt Anchor Pretensioner Deployment Control: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| B141B:11 | Second Row Driver Side Inflatable Seatbelt Deployment Control: Circuit Short to Ground | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141B:12 | Second Row Driver Side Inflatable Seatbelt Deployment Control: Circuit Short to Battery | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141B:13 | Second Row Driver Side Inflatable Seatbelt Deployment Control: Circuit Open | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141B:1A | Second Row Driver Side Inflatable Seatbelt Deployment Control: Circuit Resistance Below Threshold | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141B:2B | Second Row Driver Side Inflatable Seatbelt Deployment Control: Signal Cross Coupled | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141B:4A | Second Row Driver Side Inflatable Seatbelt Deployment Control: Incorrect Component Installed | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141C:11 | Second Row Passenger Side Inflatable Seatbelt Deployment Control: Circuit Short to Ground | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141C:12 | Second Row Passenger Side Inflatable Seatbelt Deployment Control: Circuit Short to Battery | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141C:13 | Second Row Passenger Side Inflatable Seatbelt Deployment Control: Circuit Open | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141C:1A | Second Row Passenger Side Inflatable Seatbelt Deployment Control: Circuit Resistance Below Threshold | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141C:2B | Second Row Passenger Side Inflatable Seatbelt Deployment Control: Signal Cross Coupled | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| B141C:4A | Second Row Passenger Side Inflatable Seatbelt Deployment Control: Incorrect Component Installed | INSPECT the RCM connectors for foreign material and REPAIR as necessary. If no foreign material is found, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| C0061:68 | Lateral Acceleration Sensor: Event Information | REFER to: Pinpoint Test - DTC: AA . |
| C0062:68 | Longitudinal Acceleration Sensor: Event Information | REFER to: Pinpoint Test - DTC: AA . |
| C0063:68 | Yaw Rate Sensor: Event Information | REFER to: Pinpoint Test - DTC: AA . |
| C0064:68 | Roll Rate Sensor: Event Information | REFER to: Pinpoint Test - DTC: AA . |
| C0065:68 | Vertical Acceleration Sensor: Event Information | REFER to: Pinpoint Test - DTC: AA . |
| C006A:68 | Multi-axis Acceleration Sensor: Event Information | REFER to: Pinpoint Test - DTC: AA . |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | REFER to: Pinpoint Test - DTC: BB . |
| U0028:88 | Vehicle Communication Bus A: Bus Off | REFER to: Pinpoint Test - DTC: CC . |
| U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in the pinpoint test. REFER to: Pinpoint Test - DTC: QQ
. |
| U0140:00 | Lost Communication with Body Control Module: No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in the pinpoint test. REFER to: Pinpoint Test - DTC: II
. |
| U0154:00 | Lost Communication with Restraints Occupation Classification System Module: No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in the pinpoint test. REFER to: Pinpoint Test - DTC: DD
. |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in the pinpoint test. REFER to: Pinpoint Test - DTC: EE
. |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | Using a diagnostic scan tool, CARRY OUT RCM PMI. REPEAT the RCM self-test. If RCM DTC U0300:00 is retrieved on-demand during self-test, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . |
| U0401:00 | Invalid Data Received From ECM/PCM "A": No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in a pinpoint test. CHECK for additional RCM and PCM Diagnostic Trouble Codes (DTCs). DIAGNOSE and REPAIR any Diagnostic Trouble Codes (DTCs) that are retrieved. For RCM Diagnostic Trouble Codes (DTCs), REFER to DTC Chart: Restraint Control Module (RCM)
. For BCM Diagnostic Trouble Codes (DTCs), Refer to the appropriate Engine article for the procedure. |
| U0401:81 | Invalid Data Received From ECM/PCM "A": Invalid Serial Data Received |
NOTE:
This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in a pinpoint test. CHECK for additional RCM and PCM Diagnostic Trouble Codes (DTCs). DIAGNOSE and REPAIR any Diagnostic Trouble Codes (DTCs) that are retrieved. For RCM Diagnostic Trouble Codes (DTCs), REFER to DTC Chart: Restraint Control Module (RCM)
. For BCM Diagnostic Trouble Codes (DTCs), Refer to the appropriate Engine article for the procedure. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in a pinpoint test. CHECK for additional RCM and BCM Diagnostic Trouble Codes (DTCs). DIAGNOSE and REPAIR any Diagnostic Trouble Codes (DTCs) that are retrieved. For RCM Diagnostic Trouble Codes (DTCs), REFER to DTC Chart: Restraint Control Module (RCM)
. For BCM Diagnostic Trouble Codes (DTCs), REFER to: Body Control Module (BCM)
. |
| U0422:81 | Invalid Data Received From Body Control Module: Invalid Serial Data Received |
NOTE:
This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in a pinpoint test. CHECK for additional RCM and BCM Diagnostic Trouble Codes (DTCs). DIAGNOSE and REPAIR any Diagnostic Trouble Codes (DTCs) that are retrieved. For RCM Diagnostic Trouble Codes (DTCs), REFER to DTC Chart: Restraint Control Module (RCM)
. For BCM Diagnostic Trouble Codes (DTCs), REFER to: Body Control Module (BCM)
. |
| U0422:82 | Invalid Data Received From Body Control Module: Alive / Sequence Counter Incorrect / Not Updated |
NOTE:
This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in a pinpoint test. CHECK for additional RCM and BCM Diagnostic Trouble Codes (DTCs). DIAGNOSE and REPAIR any Diagnostic Trouble Codes (DTCs) that are retrieved. For RCM Diagnostic Trouble Codes (DTCs), REFER to DTC Chart: Restraint Control Module (RCM)
. For BCM Diagnostic Trouble Codes (DTCs), REFER to: Body Control Module (BCM)
. |
| U0455:81 | Invalid Data Received From Occupant Classification System Module: Invalid Serial Data Received |
NOTE:
This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in a pinpoint test. CHECK for additional RCM and OCSM Diagnostic Trouble Codes (DTCs). DIAGNOSE and REPAIR any Diagnostic Trouble Codes (DTCs) that are retrieved. For RCM Diagnostic Trouble Codes (DTCs), REFER to DTC Chart: Restraint Control Module (RCM)
. For OCSM Diagnostic Trouble Codes (DTCs), REFER to DTC Chart: Occupant Classification System Module (OCSM)
. |
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information |
NOTE:
This DTC sets in a module that is reporting a missing or invalid message from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of the repair unless directed to do so in a pinpoint test. CHECK for additional RCM and APIM Diagnostic Trouble Codes (DTCs). For RCM Diagnostic Trouble Codes (DTCs), REFER to DTC Chart: Restraint Control Module (RCM)
. For APIM Diagnostic Trouble Codes (DTCs), Refer to the appropriate Information and Entertainment System article for the procedure. |
| U1A14:55 | CAN Initialisation Failure: Not Configured | DIAGNOSE all other RCM Diagnostic Trouble Codes (DTCs) first. If no other RCM Diagnostic Trouble Codes (DTCs) are present, REFER to: Pinpoint Test - DTC: BB . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to incomplete or improper PMI procedures. CARRY OUT the PMI procedure as directed by the diagnostic scan tool. USE As-Built data when carrying out PMI for this DTC. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CARRY OUT PMI using As-Built data. RETRIEVE RCM Diagnostic Trouble Codes (DTCs). If RCM DTC U2101:00 is retrieved on-demand, INSTALL a new RCM. Use As-Built data when carrying out PMI for this DTC. REFER to: Restraints Control Module (RCM) . |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | INSTALL a new RCM and CARRY OUT PMI using a diagnostic scan tool. USE As-Built data when carrying out PMI for this DTC. REFER to: Restraints Control Module (RCM) . |
| U2300:55 | Central Configuration: Not Configured | REFER to: Pinpoint Test - DTC: FF . |
| U2300:64 | Central Configuration: Signal Plausibility Failure | REFER to: Pinpoint Test - DTC: FF . |
| U3000:04 | Control Module: System Internal Failure | INSTALL a new RCM. USE As-Built data when carrying out PMI during the RCM installation. REFER to: Restraints Control Module (RCM) . |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | INSTALL a new RCM. Use As-Built data when CARRYING OUT PMI during the RCM installation. REFER to: Restraints Control Module (RCM) . |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new RCM. Using a diagnostic scan tool, CARRY OUT RCM PMI. If DTC U2200:00 is also present, USE As-Built data when carrying out PMI for this DTC. REFER to: Restraints Control Module (RCM) . |
| U3000:4A | Control Module: Incorrect Component Installed | REFER to: Pinpoint Test - DTC: Z . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | REFER to: Pinpoint Test - DTC: JJ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | REFER to: Pinpoint Test - DTC: JJ . |