Common Specifications & Procedures
ESCAPE COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | Refer to appropriate component installation procedure for Torque Specifications. | ||
| Axle Nut/Hub Nut | |||
| Rear Hub Nut | |||
| Stage 1 | 59 lb.ft (80 Nm) | ||
| Stage 2 | 90° | ||
| Battery | SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF BRAKE SYSTEM PRESSURE BLEEDING |
||
| Disc Brakes w/Torque | |||
| Front Disc | Refer to approriate component REMOVAL AND INSTALLATION procedures. | ||
| Rear Disc | Refer to approriate component REMOVAL AND INSTALLATION procedures | ||
| Charging | |||
| Generator w/Torque | GENERAL SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | ACCESSORY DRIVE (1.5L) or ACCESSORY DRIVE (2.0L) or ACCESSORY DRIVE (2.5L) | ||
| Belt Routing | |||
| 1.5L | ACCESSORY DRIVE - COMPONENT LOCATION | ||
| 2.0L | ACCESSORY DRIVE - COMPONENT LOCATION | ||
| 2.5L | ACCESSORY DRIVE - COMPONENT LOCATION | ||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS (1.5L) or SPECIFICATIONS (2.0L) or ENGINE COOLING - COMPONENT LOCATION (2.5L) | ||
| Radiator Pressure Cap | |||
| 1.5L | 17.4-21.7 psi (120-150 kPa) | ||
| 2.0L; 2.5L | 17.4-21.7 psi (120-150 kPa) | ||
| Thermostat R & I | |||
| 1.5L | THERMOSTAT HOUSING | ||
| 2.0L | THERMOSTAT HOUSING | ||
| 2.5L | THERMOSTAT HOUSING | ||
| Water Pump R & I | |||
| 1.5L | COOLANT PUMP | ||
| 2.0L | COOLANT PUMP | ||
| 2.5L | COOLANT PUMP | ||
| Engine Mechanical | |||
| 1.5L | |||
| Compression | SPECIFICATIONS | ||
| Oil Pressure (hot @ 800 RPM) | 14.5 psi (100kPa) | ||
| Oil Pressure (hot @ 2, 000 RPM) | 29 psi (200 kPa) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | Refer to appropriate component component in REMOVAL AND INSTALLATION procedures. | ||
| 2.0L | |||
| Compression | SPECIFICATIONS | ||
| Oil pressure (hot @ 2000 rpm) | 29-60 psi (200-414 kPa) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | Refer to appropriate component component in REMOVAL AND INSTALLATION procedures | ||
| 2.5L | |||
| Compression | SPECIFICATIONS | ||
| Oil pressure (hot @ 2000 rpm) | 29-60 psi (200-414 kPa) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | Refer to appropriate component component in REMOVAL AND INSTALLATION procedures. | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| 1.5L | Refer to FLEXPLATE
for sequence. Stage 1: 133 In. Lbs. (15 N.m) Stage 2: 18 Ft. Lbs. (25 N.m) Stage 3: 22 Ft. Lbs. (30 N.m) Stage 4: 90° |
||
| 2.0L | Refer to FLEXPLATE
for sequence Stage 1: 37 Ft. Lbs. (50 N.m) Stage 2: 59 Ft. Lbs. (80 N.m) Stage 3: 83 Ft. Lbs. (112 N.m) |
||
| 2.5L | Refer to FLEXPLATE
for sequence. Stage 1: 37 Ft. Lbs. (50 N.m) Stage 2: 59 Ft. Lbs. (80 N.m) Stage 3: 83 Ft. Lbs. (112 N.m) |
||
| Fuel System | |||
| Fuel Filter Location | Lifetime fuel filter (serviced as part of the Fuel Pump module). | ||
| Fuel Filter R & I | FUEL PUMP AND SENDER UNIT (1.5L) or FUEL PUMP AND SENDER UNIT (2.0L) or FUEL PUMP AND SENDER UNIT (2.5L). | ||
| Pressure Release Procedure | FUEL SYSTEM PRESSURE RELEASE (1.5L) or FUEL SYSTEM PRESSURE RELEASE (2.0L) or FUEL SYSTEM PRESSURE RELEASE (2.5). | ||
| Pressure Specification | SPECIFICATIONS (1.5L) or GENERAL SPECIFICATIONS (2.0L) or SPECIFICATIONS (2.5L) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE CHECK (1.5L) or FUEL SYSTEM PRESSURE CHECK (2.0L) or FUEL SYSTEM PRESSURE CHECK (2.5L). | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plugs | |||
| 1.5L | |||
| Number | CYFS 13Y RC | ||
| Gap | .7 mm (0.028 in) | ||
| Torque | 106 In. Lbs. (12 N.m) | ||
| 2.0L | |||
| Number | CYFS 12Y 2 | ||
| Gap | .7-.8 mm (0.028-0.031 in) | ||
| Torque | 106 In. Lbs. (12 N.m) | ||
| 2.5L | |||
| Number | AYFS 32Y R | ||
| Gap | 1.25-1.35 mm (0.049- 0.053 in.) | ||
| Torque | 106 In. Lbs. (12 N.m) | ||
| Starting | |||
| Starter w/Torque | |||
| 1.5L | 26 lb.ft (35 Nm) | ||
| 2.0L | 26 lb.ft (35 Nm) | ||
| 2.5L | Torque: 26 lb.ft (35 Nm) | ||
| Wheel Alignment | |||
| Adjustment Specifications | SPECIFICATIONS | ||
| Torque | SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 Ft. Lbs. (135 N.m) | ||