Information & Entertainment System (With: SONY Audio System) DTCS: DSP
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1045:13 | Chime: Circuit Open | REFER to: Instrumentation, Message Center and Warning Chimes . |
| B13FB:11 | Audio Enable Line: Circuit Short To Ground | GO to Pinpoint Test E |
| B13FD:13 | Chime Input 2: Circuit Open | REFER to: Instrumentation, Message Center and Warning Chimes . |
| B1A01:01 | Speaker #1: General Electrical Failure | GO to Pinpoint Test J |
| B1A01:11 | Speaker #1: Circuit Short To Ground | GO to Pinpoint Test J |
| B1A01:12 | Speaker #1: Circuit Short To Battery | GO to Pinpoint Test J |
| B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test J |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to Pinpoint Test H |
| B1A02:11 | Speaker #2: Circuit Short To Ground | GO to Pinpoint Test H |
| B1A02:12 | Speaker #2: Circuit Short To Battery | GO to Pinpoint Test H |
| B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test H |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test I |
| B1A03:11 | Speaker #3: Circuit Short To Ground | GO to Pinpoint Test I |
| B1A03:12 | Speaker #3: Circuit Short To Battery | GO to Pinpoint Test I |
| B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test I |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test O |
| B1A04:11 | Speaker #4: Circuit Short To Ground | GO to Pinpoint Test O |
| B1A04:12 | Speaker #4: Circuit Short To Battery | GO to Pinpoint Test O |
| B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test O |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test L |
| B1A06:11 | Speaker #6: Circuit Short To Ground | GO to Pinpoint Test L |
| B1A06:12 | Speaker #6: Circuit Short To Battery | GO to Pinpoint Test L |
| B1A06:13 | Speaker #6: Circuit Open | GO to Pinpoint Test L |
| B1A07:01 | Speaker #7: General Electrical Failure | GO to Pinpoint Test K |
| B1A07:11 | Speaker #7: Circuit Short To Ground | GO to Pinpoint Test K |
| B1A07:12 | Speaker #7: Circuit Short To Battery | GO to Pinpoint Test K |
| B1A07:13 | Speaker #7: Circuit Open | GO to Pinpoint Test K |
| B1A08:01 | Speaker #8: General Electrical Failure | GO to Pinpoint Test M |
| B1A08:11 | Speaker #8: Circuit Short To Ground | GO to Pinpoint Test M |
| B1A08:12 | Speaker #8: Circuit Short To Battery | GO to Pinpoint Test M |
| B1A08:13 | Speaker #8: Circuit Open | GO to Pinpoint Test M |
| B1A09:11 | Speaker #9: Circuit Short To Ground | GO to Pinpoint Test N |
| B1A09:12 | Speaker #9: Circuit Short To Battery | GO to Pinpoint Test N |
| B1A09:13 | Speaker #9: Circuit Open | GO to Pinpoint Test N |
| B1A10:11 | Speaker #10: Circuit Short To Ground | GO to Pinpoint Test N |
| B1A10:12 | Speaker #10: Circuit Short To Battery | GO to Pinpoint Test N |
| B1A10:13 | Speaker #10: Circuit Open | GO to Pinpoint Test N |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AH |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AJ |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AO |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AP |
| U0257:00 | Lost Communication With Front Controls / Display Interface Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC. Refer to: Instrumentation, Message Center and Warning Chimes . * If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom. |
| U2014:01 | Control Module Hardware: General Electrical Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the audio DSP module self-test. If DTC U2014:41 is retrieved again, INSTALL a new audio DSP module. Refer to: Audio Digital Signal Processing (DSP) Module . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the audio DSP module. If there have been recent service actions with the audio DSP module, INSTALL as-built data from PTS, using the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new audio DSP module to correct the failure to retain configuration data. Refer to: Audio Digital Signal Processing (DSP) Module . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the audio DSP module. If there have been recent service actions with the audio DSP module, INSTALL as-built data from PTS, using the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new audio DSP module to correct the failure to retain configuration data. Refer to: Audio Digital Signal Processing (DSP) Module . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the audio DSP module. If there have been recent service actions with the audio DSP module, INSTALL as-built data from PTS, using the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new audio DSP module to correct the failure to retain configuration data. Refer to: Audio Digital Signal Processing (DSP) Module . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the audio DSP module self-test. If DTC U3000:41 is retrieved again, INSTALL a new audio DSP module. Refer to: Audio Digital Signal Processing (DSP) Module . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AR |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AS |