Information & Entertainment System (With: Touchscreen Display) DTCS: ACM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1142:27 | Ignition Status 1: Signal Rate of Change Above Threshold | GO to Pinpoint Test D |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | If DTC B1A56:21 sets after running the bezel diagnostic tests, DISREGARD this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency, the test will fail. |
| B1A89:11 | Satellite Antenna: Circuit Short To Ground | For a satellite radio concern, GO to Pinpoint Test B For a SIRIUS Travel Link concern, GO to Pinpoint Test C For a navigation concern (if equipped), GO to Pinpoint Test AB For a compass concern, GO to Pinpoint Test AC |
| B1A89:13 | Satellite Antenna: Circuit Open | For a satellite radio concern, GO to Pinpoint Test B For a SIRIUS Travel Link concern, GO to Pinpoint Test C For a navigation concern (if equipped), GO to Pinpoint Test AB For a compass concern, GO to Pinpoint Test AC |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | GO to Pinpoint Test Y |
| B1D19:4B | Compact Disc Unit: Over Temperature | GO to Pinpoint Test Y |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AD |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AF |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AH |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to Pinpoint Test AK |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AO |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AP |
| U0257:00 | Lost Communication With Front Controls / Display Interface Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the ACM. If there have been recent service actions with the ACM, INSTALL as-built data from PTS, using the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. Refer to: Audio Front Control Module (ACM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the ACM. If there have been recent service actions with the ACM, INSTALL as-built data from PTS, using the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. Refer to: Audio Front Control Module (ACM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the ACM. If there have been recent service actions with the ACM, INSTALL as-built data from PTS, using the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. Refer to: Audio Front Control Module (ACM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the ACM self-test. If DTC U3000:41 is retrieved again, INSTALL a new ACM. Refer to: Audio Front Control Module (ACM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR all Continuous Memory Diagnostic Trouble Codes (CMDTCs). WAIT at least 10 seconds. RETRIEVE all Continuous Memory Diagnostic Trouble Codes (CMDTCs). If DTC U3000:42 is retrieved again, INSTALL a new ACM. Refer to: Audio Front Control Module (ACM) . |
| U3000:96 | Control Module: Component Internal Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the ACM self-test. If DTC U3000:96 is retrieved again, INSTALL a new ACM. Refer to: Audio Front Control Module (ACM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AR |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AS |