Windows & Glass DTCS: PDM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B117C:07 | Rear Power Window Up: Mechanical Failure | INITIALIZE the RH rear door window regulator motor. REFER to: Power Door Window Initialization . |
| B117C:16 | Rear Power Window Up: Circuit Voltage Below Threshold | GO to Pinpoint Test G |
| B117C:4B | Rear Power Window Up: Over Temperature | WAIT 10 minutes to allow the window motor to cool. INITIALIZE the RH rear door window regulator motor. REFER to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B117C:92 | Rear Power Window Up: Performance or Incorrect Operation | INITIALIZE the RH rear door window regulator motor. REFER to: Power Door Window Initialization . |
| B117E:07 | Front Power Window Up: Mechanical Failure | INITIALIZE the passenger door window regulator motor. REFER to: Power Door Window Initialization . |
| B117E:16 | Front Power Window Up: Circuit Voltage Below Threshold | GO to Pinpoint Test D |
| B117E:4B | Front Power Window Up: Over Temperature | WAIT 10 minutes to allow the window motor to cool. INITIALIZE the passenger door window regulator motor. REFER to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B117E:92 | Front Power Window Up: Performance or Incorrect Operation | INITIALIZE the passenger door window regulator motor. REFER to: Power Door Window Initialization . |
| B1189:11 | Front Window Position Sensor: Circuit Short To Ground | GO to Pinpoint Test D |
| B1189:16 | Front Window Position Sensor: Voltage Below Threshold | GO to Pinpoint Test D |
| B1189:17 | Front Window Position Sensor: Voltage Above Threshold | GO to Pinpoint Test D |
| B1189:29 | Front Window Position Sensor: Signal Invalid | GO to Pinpoint Test D |
| B1189:2B | Front Window Position Sensor: Signal Cross Coupled | GO to Pinpoint Test D |
| B1189:39 | Front Window Position Sensor: Signal Has Too Few Pulses | GO to Pinpoint Test D |
| B1189:3A | Front Window Position Sensor: Signal Has Too Many Pulses | GO to Pinpoint Test D |
| B1189:65 | Front Window Position Sensor: Has Too Few Transitions / Events | GO to Pinpoint Test D |
| B1189:77 | Front Window Position Sensor: Commanded Position Not Reachable | DIAGNOSE all other Diagnostic Trouble Codes (DTCs) first. If no other Diagnostic Trouble codes (DTCs) are present, INITIALIZE the RH front door window regulator motor. REFER to: Power Door Window Initialization (501-11 Glass, Frames and Mechanisms, General Procedures). VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B118A:11 | Rear Window Position Sensor: Circuit Short To Ground | GO to Pinpoint Test G |
| B118A:16 | Rear Window Position Sensor: Voltage Below Threshold | GO to Pinpoint Test G |
| B118A:17 | Rear Window Position Sensor: Voltage Above Threshold | GO to Pinpoint Test G |
| B118A:29 | Rear Window Position Sensor: Signal Invalid | GO to Pinpoint Test G |
| B118A:2B | Rear Window Position Sensor: Signal Cross Coupled | GO to Pinpoint Test G |
| B118A:39 | Rear Window Position Sensor: Signal Has Too Few Pulses | GO to Pinpoint Test G |
| B118A:3A | Rear Window Position Sensor: Signal Has Too Many Pulses | GO to Pinpoint Test G |
| B118A:65 | Rear Window Position Sensor: Has Too Few Transitions / Events | GO to Pinpoint Test G |
| B118A:77 | Rear Window Position Sensor: Commanded Position Not Reachable | DIAGNOSE all other Diagnostic Trouble Codes (DTCs) first. If no other Diagnostic Trouble codes (DTCs) are present, INITIALIZE the RH rear door window regulator motor. Refer to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B12C5:71 | Front Window Lifter Motor Up Relay: Actuator Stuck | GO to Pinpoint Test D |
| B12C6:71 | Rear Window Lifter Motor Up Relay: Actuator Stuck | GO to Pinpoint Test G |
| B12C7:71 | Rear Window Lifter Motor Down Relay: Actuator Stuck | GO to Pinpoint Test G |
| B12C8:71 | Front Window Lifter Motor Down Relay: Actuator Stuck | GO to Pinpoint Test D |
| B12E9:23 | Rear Window Local Up/Down Switch: Signal Stuck Low | GO to Pinpoint Test G |
| B12E9:24 | Rear Window Local Up/Down Switch: Signal Stuck High | GO to Pinpoint Test G |
| B13E5:23 | Passenger Power Window Switch Up: Signal Stuck Low | GO to Pinpoint Test D |
| B13E6:23 | Passenger Power Window Switch Down: Signal Stuck Low | GO to Pinpoint Test D |
| B13EF:4B | Right Rear Power Window Motor: Over Temperature | CLEAR the DTC. WAIT 10 minutes to allow the window motor to cool. INITIALIZE the RH rear door window regulator motor. REFER to: Power Door Window Initialization . VERIFY the DTC is no longer present. If the DTC returns, INSPECT the window seals, glass runs and window regulator for a binding condition. REPAIR as necessary. |
| B13F2:4B | Passenger Power Window Motor: Over Temperature | CLEAR the DTC. TEST the system for normal operation. If the DTC returns, INSTALL a new passenger door window regulator motor. REFER to: Front Door Window Regulator Motor . |
| C1B14:11 | Sensor Supply Voltage A: Circuit Short To Ground | GO to Pinpoint Test D |
| C1B14:15 | Sensor Supply Voltage A: Circuit Short To Battery or Open | GO to Pinpoint Test D |
| C1B14:16 | Sensor Supply Voltage A: Circuit Voltage Below Threshold | GO to Pinpoint Test D |
| C1B14:17 | Sensor Supply Voltage A: Circuit Voltage Above Threshold | GO to Pinpoint Test D |
| C1B1A:11 | Sensor Supply Voltage C: Circuit Short To Ground | GO to Pinpoint Test G |
| C1B1A:15 | Sensor Supply Voltage C: Circuit Short To Battery or Open | GO to Pinpoint Test G |
| C1B1A:16 | Sensor Supply Voltage C: Circuit Voltage Below Threshold | GO to Pinpoint Test G |
| C1B1A:17 | Sensor Supply Voltage C: Circuit Voltage Above Threshold | GO to Pinpoint Test G |
| U2002:24 | Switch: Signal Stuck High | GO to Pinpoint Test D |
| All other Diagnostic Trouble Codes (DTCs) | - | REFER to: Locks, Latches and Entry Systems . |