| Accelerator pedal position |
PCM |
This message is sent to the GWM and then to the ABS module. This message provides the ABS module with the current accelerator pedal position and notifies the ABS module if the data is valid or invalid. The ABS module uses accelerator pedal position information for correct operation of the traction control, ESC, RSC and hill start assist systems. |
| Adaptive cruise control deceleration |
CCM |
This message is sent to the IPMA and then to the ABS module. This message contains the amount of deceleration currently required by the adaptive cruise control system to maintain the distance gap set by the driver. |
| Adaptive cruise control braking precharge |
CCM |
This message is sent to the IPMA and then to the ABS module. This message is sent by the CCM to request precharging of the brake system in preparation for adaptive cruise control deceleration from the ABS module. |
| Adaptive cruise control braking request |
CCM |
This message is sent to the IPMA and then to the ABS module. This message is sent by the CCM to request adaptive cruise control braking from the ABS module. |
| Ambient air temperature |
PCM |
This message is sent to the GWM and then to the ABS module. The ABS module uses this information for calculations in determining the operational status of the various stability control systems and features. |
| Collision mitigation deceleration |
CCM |
This message is sent to the IPMA and then to the ABS module. This message contains the amount of deceleration currently required by the CCM to assist in collision avoidance. |
| Collision mitigation braking precharge |
CCM |
This message is sent to the IPMA and then to the ABS module. This message is sent by the CCM to request precharging of the brake system in preparation for collision mitigation deceleration from the ABS module. |
| Collision mitigation braking request |
CCM |
This message is sent to the IPMA and then to the ABS module. This message is sent by the CCM to request collision mitigation braking from the ABS module. |
| Driven wheel torque output |
PCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of the current torque output available at the driven wheels. This information is used for the traction control, hill start assist, ESC and RSC feature operation. |
| Driver seat belt buckle status |
RCM |
This message informs the ABS module of the current driver seat belt buckle status, buckled or unbuckled. The ABS module uses this information for the electric parking brake drive away release feature. |
| Door ajar status |
BCM |
This message is sent to the GWM and then to the ABS module. This information is used by the ABS module for hill start assist operation. |
| EPAS external angle request |
PSCM |
This message informs the ABS module the EPAS gear is in the process of completing a park aid steering request. |
| Engine status |
PCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of the current engine status; engine off, engine on, engine auto stopped, not used. |
| Engine RPM |
PCM |
This message is sent to the GWM and then to the ABS module. Used to inform the ABS module of the current engine RPM. The ABS module uses this information for EPB drive away release feature, traction control, ESC, RSC and hill start assist operations. |
| Hill descent control request |
IPC |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module the driver has requested the hill descent control system to be activated or deactivated. |
| Ignition key type |
BCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of the current ignition key type; standard or MyKey. The ABS modifies operating parameters if a restricted MyKey is used. |
| Ignition status |
BCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of the current ignition status; off, accessory, run, start, unknown or invalid. |
| Neutral tow command |
GSM |
This message informs the ABS module of the current transmission neutral tow status; normal mode, car wash mode, neutral tow mode or not used. |
| Neutral tow command |
TCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of the current transmission neutral tow status; normal mode, car wash mode, neutral tow mode or not used. |
| Odometer master value |
IPC |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of the current odometer mileage. |
| Parking brake request |
GSM |
This message is a request from the GSM to apply the parking brake. |
| Parking brake request |
TCM |
This message is sent to the GWM and then to the ABS module. This message is a request from the GSM to apply the parking brake. |
| Powertrain status |
PCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of the current powertrain status; off_torque not available, on_torque not available, start in progress_torque not available or on_torque available. |
| Rear differential lock status |
DCMR |
This message informs the ABS module of the current rear differential locked status; no fault, unspecified fault, differential failed open and differential failed closed. The ABS module requests rear differential unlocking during traction control, ESC and RSC operations. |
| Rear differential locking torque |
DCMR |
This message informs the ABS module of the current amount of torque being applied to the rear differential. The ABS module requests rear differential unlocking during traction control, ESC and RSC operations. |
| RCM serial number |
RCM |
This message is sent to the GWM and then to the ABS module. The ABS module stores the RCM serial number and verifies the serial number when the vehicle is started or the ignition is set to ON or ACC. Over time, the ABS module learns the offset of the stability sensors inside the RCM. When a new RCM serial number is found and the Interactive Vehicle Dynamics (IVD) Initialization procedure is carried out using a diagnostic scan tool, the ABS module resets the offset values learned for the yaw rate sensor, lateral accelerometer and roll rate sensor. |
| Reverse gear status |
PCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of the current reverse gear status; inactive not confirmed, inactive confirmed, active not confirmed, or active confirmed. This information is used for hill start assist, ESC and RSC operation. Hill start assist operates in forward and reverse gears. ESC and RSC do not operate when the transmission is in REVERSE. |
| Selectable drive mode brake request |
IPC |
This message informs the ABS module of the current brake drive mode request; Normal, Sport, Tow-Haul, Eco, Snow-Wet, Grass-Gravel-Snow, Sand or Mud-Rut. |
| Selectable drive mode chassis request |
VDM |
This message informs the ABS module of the current chassis drive mode request; Not Available, Available, Temporarily Not Available or Faulty. |
| Selectable drive mode powertrain request |
PCM |
This message informs the ABS module of the current powertrain drive mode request; Not Available, Available, Temporarily Not Available or Faulty. |
| Selectable drive mode steering status |
PSCM |
This message informs the ABS module of the current PSCM selectable drive mode switch status; Not Available, Available, Temporarily Not Available or Faulty. |
| Selectable drive mode suspension status |
VDM |
This message informs the ABS module of the current VDM selectable drive mode switch status; Not Available, Available, Temporarily Not Available or Faulty. |
| Selectable drive mode switch status |
TCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of the current selectable drive mode switch status; not pressed, switch state 1, switch state 2, or faulty. |
| Selectable drive mode switch status |
ATCM |
This message informs the ABS module of the current selectable drive mode switch status; not pressed, switch state 1, switch state 2, or faulty. |
| Stability-traction control mode request |
IPC |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module the driver has requested a change to enable or disable the traction control, ESC or RSC. |
| Stability-traction control MyKey request |
IPC |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module the MyKey feature has been configured to "Always On". |
| Steering wheel angle information |
PSCM |
The ABS module uses steering angle sensor information for ESC and RSC operation. This message provides the ABS module with the current steering wheel angle in degrees as well as the steering wheel angle count (number or revolutions). |
| Trailer brake control connection |
TBM |
This message informs the ABS module a trailer is connected to the vehicle. The ABS module uses this information for trailer sway control operation. |
| Trailer brake lamp connection |
TRM |
This message informs the ABS module a trailer with brake lamps is connected to the vehicle. |
| Trailer sway control configuration |
IPC |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module the driver has requested the trailer sway control system to be activated or deactivated. |
| Transfer case lock status |
TCCM |
This message informs the ABS module of the current transfer case locked status; OK, opened by command, inactive, fault, warning, disabled, fully locked by command, torque limited by command, under external torque control and undefined. The ABS module requests transfer case unlocking during traction control, ESC and RSC operations. |
| Transfer case locking torque |
TCCM |
This message informs the ABS module of the current amount of torque being applied to the transfer case. The ABS module requests transfer case unlocking during traction control, ESC and RSC operations. |
| Transfer case range |
TCCM |
This message informs the ABS module of the current transfer case range; low, neutral or high. The ABS module modifies the thresholds for traction control, ESC and RSC intervention based on the current transfer case range. |
| Transmission range request |
TCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module of which gear the transmission is currently using. This information is used for hill start assist, ESC and RSC operation. Hill start assist operates in forward and reverse gears. ESC and RSC do not operate when the transmission is in REVERSE. |
| Transmission shift active |
TCM |
This message is sent to the GWM and then to the ABS module. This message informs the ABS module when the automatic transmission is changing gears. |
| Vehicle configuration data |
BCM |
This message is sent to the GWM and then to the ABS module. This message provides the ABS module with the current optional and configured items such as tire size, axle ratio, manual or automatic transaxle, keyless entry and VIN. |
| Vehicle lateral acceleration data |
RCM |
This message provides the ABS module with the current vehicle lateral acceleration data and notifies the ABS module if the data is valid or invalid. The ABS module uses the lateral acceleration data for traction control, ESC and RSC feature operation. |
| Vehicle longitudinal acceleration data |
RCM |
This message provides the ABS module with the current vehicle longitudinal acceleration data and notifies the ABS module if the data is valid or invalid. The ABS module uses the longitudinal acceleration data for ESC and RSC feature operation. |
| Vehicle speed |
PCM |
This message is sent to the GWM and then to the ABS module. This message provides the ABS module with the current vehicle speed in kilometers per hour and notifies the ABS module if the data is valid or invalid. |
| Vehicle yaw rate data |
RCM |
This message provides the ABS module with the current vehicle yaw rate data and notifies the ABS module if the data is valid or invalid. The ABS module uses the yaw rate data for ESC and RSC feature operation. |